94536M Mariner GROMMET


94536M GROMMET Mariner 7040202, 7040206, 7040207PW, 7040208, 7040328, 7040507, 7040706, 7040716 GROMMET
94536M GROMMET Mariner
Rating:
53

Buy GROMMET 94536M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

Mariner entire parts catalog list:

7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040207PW 1989,1990,1991,1992,1993
7040208 1978
7040328 1978,1980
7040507 1987
7040706 1986,1990,1992
7040716 1986

Information:


Illustration 1 g01303631
Schematic for the analog sensor
Test Step 1. INSPECT THE ELECTRICAL CONNECTORS AND WIRING
Remove the electrical power from the engine. Note: For the following steps, refer to Troubleshooting, "Electrical Connectors - Inspect".
Thoroughly inspect each of the following connectors:
J1/P1 connectors
J7/P7 connectors
Check the torque of the allen head screws for the ECM connectors.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit for the analog sensors.
Check the harness and wiring for abrasion and for pinch points from the analog sensors to the master ECM. Expected Result:All connectors, pins, and sockets are connected properly. The connectors and the wiring do not have corrosion, abrasion, or pinch points.Results:
OK - All connectors, pins, and sockets are connected properly. The connectors and the wiring do not have corrosion, abrasion, or pinch points. The components are in good condition with proper connections. If you are troubleshooting a -3 code, proceed to Test Step 3. If you are troubleshooting a -4 code, proceed to Test Step 2.
Not OK - At least one of the connectors, pins, and/or sockets are not connected properly. At least one of the connectors and/or the wiring has corrosion, abrasion, or pinch points.Repair: Perform the necessary repairs and/or replace parts, if necessary.STOPTest Step 2. CREATE AN OPEN CIRCUIT FOR THE SENSOR
Disconnect the sensor that has the "voltage below normal" diagnostic code.
Observe the "Active Diagnostic" screen on Cat ET. Allow a minimum of 30 seconds for any codes to activate. Look for an active -3 diagnostic code. Expected Result:There is an active -3 diagnostic code for the disconnected sensor.Results:
Yes - Before the suspect sensor was disconnected, there was an active -4 diagnostic code for the sensor. After the suspect sensor was disconnected, there was an active -3 diagnostic code for the sensor.Repair: Reconnect the sensor. If the active -4 diagnostic code recurs, replace the original sensor.Verify that the code does not activate when the new sensor is installed. Clear the logged codes from the master ECM.STOP
No - Before the suspect sensor was disconnected, there was an active -4 diagnostic code for the sensor. After the suspect sensor was disconnected, the active -4 diagnostic code remained. Proceed to Test Step 3.Test Step 3. CHECK THE PULL-UP VOLTAGE AT THE SENSOR
Verify that the suspect sensor's connector is disconnected from the engine harness.
Illustration 2 g01303636
Harness connectors for the sensor
(1) Signal
(2) Return
At the harness connector for the suspect sensor, measure the voltage between terminals (1) and (2). Expected Result:The voltage is between 6.0 VDC and 7.0 VDC.Results:
OK - The voltage between the signal terminal and the return terminal is between 6.0 VDC and 7.0 VDC. The pull-up voltage that is created by the master ECM is present at the sensor connector. The signal wire and the return wire for the suspect sensor appear to be OK. Proceed to Test Step 5.
Not OK - The voltage between the signal terminal and the return terminal is not between 6.0 VDC and 7.0 VDC. The pull-up voltage that is created by the master ECM is not present at the sensor connector. Proceed to Test Step 4.Test Step 4. CHECK THE PULL-UP VOLTAGE AT THE MASTER ECM
Use a 151-6320 Wire Removal Tool to remove the signal wire for the suspect sensor from the P1 connector.
Use a jumper wire with


Parts grommet Mariner:

81589M
 
81589M GROMMET, BOTTOM COWL (MANUAL)
7028207, 7028527, 7040207, 7040208, 7040507
82063M
 
82063M GROMMET, CHOKE KNOB
7028207, 7028527, 7040207, 7040208, 7040507
82069M
 
82069M GROMMET
7008218EW, 7008425, 7010209, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040208, 7040328, 7040706, 7040716, 7048207, 7048227, 7048321, 7055524, 7060507,
84760M
 
84760M GROMMET
7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716
83607M
 
83607M GROMMET
7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040716
11710M
 
11710M GROMMET
7040207PW, 7040208PW, 7055324
11687M
 
11687M GROMMET
7040207PW, 7040208PW
11688M
 
11688M GROMMET
7040207PW, 7040208PW
Back to top