824934A 1 Mariner HARNESS ASSEMBLY


824934A 1 HARNESS ASSEMBLY Mariner 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY, 7100412CD, 7100412HB, 7115412TB HARNESS
824934A 1 HARNESS ASSEMBLY Mariner
Rating:
63

Buy HARNESS ASSEMBLY 824934A 1 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

Mariner entire parts catalog list:

7075217CD 1994,1995,1996,1997,1998
7075217HD 1999,2000,2001,2002,2003,2004
7075217TD 2005
7075217UD 2006
70752L7TF 2005
70752L7UF 2006
7075317TB 2005
7075317UB 2006
7075412TB 2005
7075412UB 2006
7075412UY 2006
7090412TB 2005
7090412TD 2005
7090412TY 2005
7090412UB 2006
7090412UY 2006
7100412CD 1994,1995,1996,1997,1998
7100412HB 1999,2000,2001,2002,2003,2004
7115412TB 2005,2006

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
B 1P-1861 Retaining Ring Pliers 1
C 271-0498 Piston Ring Expander 1
H 1U-7616 Piston Ring Compressor 1
J 334-0519 Grease 1
K 364-2837 (1) Installer As 1
(1) For use with 350-0074 Cylinder Liner.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00582421
Use Tooling (C) to install piston rings (6) on piston (3).
The ends of the oil control piston ring should be 180 degrees away from the oil ring end gap. The white-colored section of the oil ring spring should also be visible at the oil ring end gap.
Install the intermediate ring with the side that is marked "UP" toward the top of the piston. Position the intermediate ring with the green strip on the right side of the end gap.
Install the top piston ring with the red strip on the right side of the end gap.
The piston ring end gaps must be approximately 120 degrees away from each other after installation.
Illustration 2 g01051820
Place clean engine oil on piston pin (4), the piston pin bearing, and the bore in piston pin (4).
Position connecting rod (5) in piston (3) and install piston pin (4).
Use Tooling (B) to install the retaining rings that hold piston pin (4).
Install the upper half of the connecting rod bearing in connecting rod (5). Ensure that the tab on the back of the bearing is in the bearing tab groove on connecting rod (5).
Illustration 3 g02340238
Apply clean engine oil to the cylinder liner bore.
If necessary, install Tooling (K) in the top of the cylinder liner.
Illustration 4 g01056335
Improper installation of the piston and connecting rod assembly will result in severe damage to the engine.Make sure that the side of the connecting rod bore with the chamfer is oriented next to the surface of the crankshaft thrust plate. The square side of the connecting rod bore must be next to the other connecting rod that is on the same crankshaft journal.
Place clean engine oil on the piston rings and the cylinder liner bore. Use Tooling (H) to compress the piston rings.
Install the piston and connecting rod assembly in the engine.
Illustration 5 g00582418
Install the lower half of the connecting rod bearing in connecting rod cap (2). Ensure that the tab on the back of the bearing is in the bearing tab groove on connecting rod cap (2).
Check the clearance of the bearings. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the correct procedure.
Place clean engine oil on the upper half and on the lower half of the connecting rod bearing.
Apply Tooling (J) to the threads of the bolts and the threads in connecting rod caps (2).
Position connecting rod cap (2) on the connecting rod and install bolts (1) in connecting rod cap (2).
Illustration 6 g01087388
(12) Side of the connecting rod with the chamfer
(13) Location pin
Tighten Bolts (A) and (B) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolts (C) and (D) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolts (C) and (D) again to a torque of 90 5 N m (65 4 lb ft).
Tighten all of the bolts for an additional 90 5 degrees.
Check the side clearance that is between two of the connecting rods that are on the same journal. The clearance must be 0.85 0.332 mm (0.034 0.0130 inch).
Use Tooling (A) to turn the engine in order to access the bolts in the connecting rod cap. End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install".
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".


Parts harness Mariner:

43442A 3
 
43442A 3 HARNESS ASSEMBLY, Primary
7100412CD, 7100412NC
819514A 4
 
819514A 4 HARNESS ASSEMBLY, Trim
7075217CD, 7100412CD, 7100412NC
12649A 4
 
12649A 4 HARNESS ASSEMBLY
7050302ED, 7050412YD, 7060412ET, 7075217CD, 7115F13KD, 7115F13RD, 7F75411JD, 7F75412RD, 7F75413TD
11149A 8
 
11149A 8 HARNESS ADAPTOR
7075217CD, 7100412CD
855212A 1
 
855212A 1 HARNESS-ADAPTOR
7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY, 7100412CD, 7100412HB, 7115412TB
850043A 2
 
850043A 2 HARNESS-ENGINE
7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY, 7100412CD, 7100412HB, 7115412TB
850046A 2
 
850046A 2 HARNESS-IGNITION
7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY
850044A 2
 
850044A 2 HARNESS-ENGINE
7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY
Back to top