898101144 Mariner HARNESS ASSEMBLY, Extension-PTT


898101144 HARNESS ASSEMBLY, Extension-PTT Mariner 7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK HARNESS
898101144 HARNESS ASSEMBLY, Extension-PTT Mariner
Rating:
38

Buy HARNESS ASSEMBLY, Extension-PTT 898101144 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Compatible models:

Mariner entire parts catalog list:

7A25203UK 2006,2010
7A25213UL 2006
7A25302UL 2006
7A3G312UK 2006

Information:

1. Check each bearing cap (1) for its location on the engine. Each cap has an arrow which is toward the front of the block and a number which gives the location of that cap. Keep each bearing with the correct cap.2. Remove bearing caps No. 2 through No. 4. Remove thrust plates from No. 3 upper bearing.
Be careful not to cause damage to the crankshaft journals when the crankshaft is removed.
3. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft as shown. Remove No. 1 and No. 5 main bearing caps. Remove the crankshaft. Weight of the crankshaft is 270 lb. (122 kg). 4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface 0.025 0.02 in. (6.4 0.5 mm).2. Install dowel (2) until it is extended from the surface 0.16 0.02 in. (4.1 0.5 mm). 3. Heat crankshaft gear (3) to a maximum temperature of 400°F (204°C). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2).4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft.
Do not cause damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block. For more detail about installation of main bearings see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS.6. Check the bearing clearance with Plastigage.7. Put clean engine oil on the bolts for caps No. 1 and No. 5. Install No. 1 and No. 5 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block. 8. Install thrust plates (5) for the No. 3 upper main bearing. Install the thrust plates with the side that has the identification "Block Side" toward the cylinder block.9. Put clean oil on the bolts for caps No. 2 through No. 4. Install caps No. 2 through No. 4 with the bolts finger tight. Make sure the arrows are toward the front of the block.10. Tighten the cap bolts as follows: a) Tighten the bolts on the tab end of the caps first to a torque of 190 10 lb.ft. (260 14 N m).b) Tighten the bolts on the other end of the caps to a torque of 190 10 lb.ft. (260 14 N m).c) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120°. 11. Check the play of the crankshaft with tool (A). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.006 to 0.020 in. (0.152 to 0.508 mm). The maximum end play with used thrust plates is 0.035 in. (0.89 mm).end by:a) install pistonsb) install flywheel housingc) install timing gear coverd) install oil pump


Parts harness Mariner:

898101T52
 
898101T52 HARNESS ASSEMBLY, ECU
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK
898101T51
 
898101T51 HARNESS ASSEMBLY, ECU
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK
898101175
 
898101175 HARNESS ASSEMBLY, Solenoid Switch - Red
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK
Back to top