99695A 1 Mariner HARNESS ASSEMBLY, Control, POWER TRIM


99695A 1 HARNESS ASSEMBLY, Control, POWER TRIM Mariner 7045217, 7050717, 7060312PC, 7075524, 7075717, 7090524, 7115520, 7135826, 7150629, 7175629, 7200620, 7220727 HARNESS
99695A 1 HARNESS ASSEMBLY, Control, POWER TRIM Mariner
Rating:
103

Buy HARNESS ASSEMBLY, Control, POWER TRIM 99695A 1 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 30
 

Mariner entire parts catalog list:

7045217 1987,1988,1989
7050717 1987,1988,1989,1990
7060312PC 1989
7075524 1984,1985,1986
7075717 1987,1989
7090524 1984,1985,1986,1987,1988
7115520 1980
7135826 1986,1987,1988
7150629 1979,1980,1982,1984,1985
7175629 1979,1980,1985,1986,1988
7200620 1980,1982,1983,1984,1985,1986,1988
7220727 1987,1988

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     177-7861     Hose As     1    
6V-4143 Couplers     2    
8T-0860 Pressure Gauge (0 to 40,000-kPa (0 to 5,800-psi))     1    Note: Permit only one operator on the machine. Keep all other personnel away from the machine or in the operator's sight.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Move the machine to a hard, level surface.
Place the transmission direction and speed control in the NEUTRAL position and in any speed position. Engage the steering and transmission lock lever on STIC steering machines.
Engage the parking brake. Place wheel blocks in front of the wheels and behind the wheels.
When the work tool is raised for testing or for adjusting, make sure that the work tool is supported correctly. Also, make sure that the bucket and/or attachment is fully in the DUMP position. The lift circuit has high oil pressure when the lift arms raise the front of the machine.Note: Do not stop the machine with the front of the machine off the ground unless this is required for a test. Lower the machine to the ground and stop the engine.
If the machine is equipped with the ride control system, with the engine speed above 1500 rpm, press and hold the ride control switch to the SERVICE position. Move the joystick control lever to the FLOAT position. This will relieve all of the hydraulic pressure in the ride control accumulator.
Decrease the engine speed to low idle.
Stop the engine.
Install the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Move the key start switch to the ON position.
Move the joystick control lever through the full range of travel. This will relieve any pressure that may be present in the implement hydraulic system.
Move the steering control several times in both directions to release the pressure in the steering system.
Depress the brake pedal at least 80 times to release any pressure in the braking system.
Depress the breaker relief valve on the hydraulic tank to release the pressure in the hydraulic tank.
Illustration 1 g00975402
(1) Pressure tap (for the rod end of the tilt cylinder) (2) Pressure tap (for the head end of the tilt cylinder)
Connect Tooling (A) to pressure tap (1). If there is any pressure on the gauge, move the joystick control lever to all positions until all the pressure is removed from the system.
Connect Tooling (A) to pressure tap (2). If there is any pressure on the gauge, move the joystick control lever to all positions until all the pressure is removed from the system.
The pressure in the hydraulic system has now been released. The lines, fittings and components can be removed.
Remove the test equipment.


Parts harness Mariner:

77617
 
77617 HARNESS, PRIMARY (CYLINDERS 1 AND 2)
7075524, 7080508, 7080629, 7085507
77618
 
77618 HARNESS, PRIMARY (CYLINDERS 3 AND 4)
7075524, 7080508, 7080629, 7085507
85537A 2
 
85537A 2 HARNESS ASSEMBLY, COIL TO SWITCH BOX (#2, 4 AND 6)
7090520, 7090524, 7090529, 7115520, 7115529, 7140629
85537A 1
 
85537A 1 HARNESS ASSEMBLY, COIL TO SWITCH BOX (#1, 3 AND 5
7090520, 7090524, 7090529, 7115520, 7115529, 7140629
69738A 7
69108A 1
13397A 1
 
13397A 1 HARNESS ASSEMBLY (Use where Applicable)
71354120D, 7135826, 7150453ND, 7175629, 7200412PD, 7200620, 7220727
88721A 1
Back to top