813715A13 Mariner HI-TENSION CABLE KIT


813715A13 HI-TENSION CABLE KIT Mariner 7031203GD, 7031207CD HI
813715A13 HI-TENSION CABLE KIT Mariner
Rating:
78

Buy HI-TENSION CABLE KIT 813715A13 Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$15.62
 

14-08-2024
0.19[0.09] Pounds
US: Big Wide Seller
MERCURY CABLE SET-IGN
MERCURY
Number on catalog scheme: 40
 

Compatible models:

Mariner entire parts catalog list:

7031203GD 1998,1999
7031207CD 1994,1995,1996,1997,1998

Information:

The Secondary Fuel Filter Has Been Replaced
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Note: Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for information on replacing the filter.
Turn the ignition switch to the "OFF" position.
Illustration 1 g00634216
Typical example
(1) Air purge screw
(2) Fuel pressure regulating valve
(3) Hand priming pump (IF EQUIPPED)
Open air purge screw (1) for the fuel filter by three full turns. Do not remove the air purge screw.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Start the engine. The engine should start and the engine should run smoothly. Note: You may use the hand priming pump for the fuel filter (IF EQUIPPED) instead of starting engine and running the engine.
While the engine is running, observe air purge screw (1). When a small drop of fuel appears at the threads of the air purge screw, close and tighten air purge screw (1). Note: There may be a noticeable change in the sound of the running engine when the air purge screw is tightened. The change in the sound of the engine is normal.Note: Failure to tighten all fittings could result in serious fuel leaks.
Clean any residual fuel from the engine components. The Engine Has Been Run Out of Fuel
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Turn the ignition switch to the "OFF" position.
Fill the fuel tank(s) with clean diesel fuel.
Illustration 2 g00634216
Typical example
(1) Air purge screw
(2) Fuel pressure regulating valve
(3) Hand priming pump (IF EQUIPPED)
Open fuel pressure regulating valve (2) by two and a half turns. The regulating valve is located in the integral fuel filter base. Note: Do not remove the regulating valve completely. Open the valve enough to allow the air that is trapped in the cylinder head to be purged from the fuel system.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Crank the engine for 30 seconds. Use a suitable container to catch the fuel while you crank the engine. Allow the starter motor to cool for 2 minutes. Note: You may use the hand priming pump (3) (IF EQUIPPED) for the fuel filter instead of cranking the engine.
Crank the engine for 30 seconds. Allow the starter motor to cool for 2 minutes.
Close and tighten fuel pressure regulating valve (2).
Crank the engine for 30 seconds. Allow the starter motor to cool for 2 minutes.
Repeat Step 7 until the engine starts and the engine runs. Note: Failure to tighten all fittings could result in serious fuel leaks.
Clean any residual fuel from the engine components.


Parts hi Mariner:

821945A61
 
821945A61 HI-TENSION CABLE
7031203GD, 7031207CD, 70432037D, 7055207GD, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY, 7100412CD, 7100412HB, 7115412T
Back to top