895157001 Mariner HOLDER, Breaker

Part No. 6V-5582When the electric starting motor is viewed from the drive end, the motor rotates in the following direction ... ClockwiseNo load conditions at 25°C (77°F)Maximum speed with no load ... 3300 rpmMaximum current with no load ... 80 ampVoltage ... 23.5 V(1) Battery terminal A maximum of three cable or wire terminals should be between the nuts.Tighten the nut on the battery terminal to the following torque ... 30.5 3.5 N m (22 3 lb ft)(2) Ground terminal Tighten the nut on the ground terminal to the following torque ... 1.5 0.5 N m (13 4 lb inch)(3) Ground terminal Tighten the nut on the ground terminal to the following torque ... 30.5 3.5 N m (22 3 lb ft)(4) Switch terminal The wire terminal that is on the switch terminal must be insulated with heat shrink tubing. Do not use moulded terminals.Tighten the nut on the switch terminal to the following torque ... 2.25 0.25 N m (20 2 lb inch)(5) Motor terminal Tighten the nut on the motor terminal to the following torque ... 30.5 3.5 N m (22 3 lb ft)(6) Motor frame terminal Tighten the nut on the motor frame terminal to the following torque ... 17.5 2.5 N m (13 2 lb ft) SolenoidCurrent draw at 24 V and 25 °C (77 °F)Pull-in windings ... 103 AmpHold-in windings ... 19 Amp maximum Delco-Remy Part No. 106-8554When the electric starting motor is viewed from the drive end, the motor rotates in the following direction ... ClockwiseNo load conditions at 25°C (77°F)Speed ... 7643 1683 rpmCurrent draw ... 67.5 7.5 ampVoltage ... 23 V(1) Battery terminal A maximum of three cable or wire terminals should be between the nuts.Tighten the nut on the battery terminal to the following torque ... 30.5 3.5 N m (22 3 lb ft)(2) Ground terminal Tighten the nut on the ground terminal to the following torque ... 30.5 3.5 N m (22 3 lb ft)(3) Ground terminal Tighten the nut on the ground terminal to the following torque ... 2.25 0.25 N m (20 2 lb inch)(4) Switch terminal The wire terminal that is on the switch terminal must be insulated with heat shrink tubing. Do not use moulded terminals.Tighten the nut on the switch terminal to the following torque ... 2.25 0.25 N m (20 2 lb inch)(5) Motor terminal Tighten the nut on the motor terminal to the following torque ... 30.5 3.5 N m (22 3 lb ft)(6) Motor frame terminal Tighten the nut on the motor frame terminal to the following torque ... 8 3 N m (72 24 lb inch)Clearance between the pinion and the housing ... 9.1 mm (.36 inch) SolenoidCurrent draw at 20 V and 25 °C (77 °F)Pull-in windings ... 56.5 4.5 AmpHold-in windings ... 14.6 Amp maximum Bosch Part No. 6V-5540When the electric starting motor is viewed from the drive end, the motor rotates in the following direction ... ClockwiseNo load conditions at 25 °C (77 °F) Speed ... 5500 rpm minimumCurrent draw ... 140 amp maximumVoltage ... 24 V(1) Battery terminal A maximum of three cable or wire terminals should be between the nuts.Tighten the nut on the battery terminal to the following torque ... 30.5 3.5 N m (22 3 lb ft)(2) Ground terminal Tighten the nut on the ground terminal to the following torque ... 30.5 3.5 N m (22 3 lb ft)(3) Ground terminal Tighten the nut on the ground terminal to the following torque ... 2.25 0.25 N m (20 2 lb inch)(4) Switch terminal The wire terminal that is on the switch terminal must be insulated with heat shrink tubing. Do not use moulded terminals.Tighten the nut on the switch terminal to the following torque ... 2.25 0.25 N m (20 2 lb inch)(5) Motor terminal Tighten the nut on the motor terminal to the following torque ... 30.5 3.5 N m (22 3 lb ft)(6) Motor frame terminal Tighten the nut on the motor frame terminal to the following torque ... 30.5 3.5 N m (22 3 lb ft)Clearance between the pinion and the housing ... 8.3 to 9.9 mm (.33 to .39 inch) SolenoidCurrent draw at 24 V and 25 °C (77 °F) Pull-in windings ... 51 AmpHold-in windings ... 7 Amp maximum