855258 84 Mariner HOSE, (32.00 Inches) (Cut to 8 Inches


855258 84 HOSE, (32.00 Inches) (Cut to 8 Inches Mariner 7075D73UY, 7075D73ZY, 7090D73RD HOSE
855258 84 HOSE, (32.00 Inches) (Cut to 8 Inches Mariner
Rating:
33

Buy HOSE, (32.00 Inches) (Cut to 8 Inches 855258 84 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Mariner entire parts catalog list:

7075D73UY 2006
7075D73ZY 2006
7090D73RD 2004,2005

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 589-7433 Link Bracket 2
B - Loctite ® C5-A (North America) -
Loctite ® 8008 (Outside North America) -
C 207-1601 Rubber Lubricant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the spacer plate and the surface of the cylinder block are clean.
Illustration 1 g06553514
Ensure that the surface of the spacer plate gasket and the surface of the cylinder block are clean. Do not use a gasket adhesive on these surfaces.
Install a new gasket (18) on the dowels in the cylinder block.
Install O-ring seal (19).
Illustration 2 g06553497
Install spacer plate (17) and cylinder head gasket (16) on the dowels in the cylinder block.
Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liner Projection" for the correct procedure.
Illustration 3 g06553298
Install seals (13) and seals (14).
Apply Tooling (C) to the bore of the inlet tube assembly. Install O-ring seal (11) in the inlet tube assembly.
Install gasket (12) on the exhaust manifold.
Install O-ring seal (15) on the dowel.
Illustration 4 g06554112
Install plug (20).
Illustration 5 g06554127
Install Tooling (A) onto cylinder head assembly (10). Attach a suitable lifting device to Tooling (A). The weight of cylinder head assembly (7) is approximately 47 kg (104 lb).
Ensure that the bottom of the cylinder head assembly is thoroughly clean.
Illustration 6 g06552788
Lift the cylinder head assembly into position on the cylinder block. Install bolts (8) and bolts (9) according to the instructions in Step 15 or Step 16.Note: Only 216 mm (8.5 inch) bolts (8) can be used for the following torque procedures.Note: Refer to Specifications, "Cylinder Head".
Remove Tooling (A) from the cylinder head.
Illustration 7 g06554187
Tightening sequence with 362-8264 Cylinder Head Gasket (MLS) and 519-7297 Spacer Plate (Iron).Note: Refer to Illustration 7 for the correct tightening sequence.
Coat the threads of the bolts with clean engine oil.
Tighten bolt (1) through bolt (8) to a torque of 30 5 N m (22 4 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 145 15 N m (107 11 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 145 15 N m (107 11 lb ft).
Turn bolt (1) through bolt (8) an angle of 180 5 degrees.
Tighten bolts (9) and (10) to a torque of 55 10 N m (40 7 lb ft).
Illustration 8 g06554195
Tightening sequence with 110-6991 Cylinder Head Gasket (Cellulose) and 110-6994 Spacer Plate (Aluminum) or 362-9677 Spacer Plate (Aluminum).Note: The cellulose head gasket cannot be used with an iron spacer plate.Note: Refer to Illustration 8 for the correct tightening sequence.
Tighten bolt (1) through bolt (8) to a torque of 30 5 N m (22 4 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 200 15 N m (148 11 lb ft).
Tighten bolt (1) through bolt (8) again to a torque of 200 15 N m (148 11 lb ft).
Turn bolt (1) through bolt (8) to an angle of 180 degrees.
Tighten bolt (9) and bolt (10) to a torque of 55 10 N m (41 7 lb ft).


Parts hose Mariner:

892156A01
 
892156A01 HOSE ASSEMBLY, Water Pressure
7075D73UY, 7075D73ZY, 7090D73RD
883069 55
 
883069 55 HOSE, (.125 x 25.00 Inches)
7075D73UY, 7075D73ZY, 7090D73RD
885376
 
885376 HOSE, Air
7075D73UY, 7075D73ZY, 7090D73RD
881041A 1
 
881041A 1 HOSE ASSEMBLY, Air By-Pass
7075D73UY, 7075D73ZY, 7090D73RD
858339 39
 
858339 39 HOSE, (17.00 Inches Bulk) (Cut to 4-1/2 Inches
7075D73UY, 7075D73ZY, 7090D73RD, 7135D73RD, 7135D73UY, 7135D73ZY
889712001
 
889712001 HOSE, Vent, To Vent Fitting
7075D73UY, 7075D73ZY, 7090D73RD
881040A 1
 
881040A 1 HOSE ASSEMBLY, Fuel Supply
7075D73UY, 7075D73ZY, 7090D73RD
878506A 1
 
878506A 1 HOSE ASSEMBLY, Fuel By-Pass
7075D73UY, 7075D73ZY, 7090D73RD
Back to top