7370A13 Mariner IGNITION COIL ASSEMBLY


7370A13 IGNITION COIL ASSEMBLY Mariner 7002201DK, 7008237, 7020201NC, 7020207, 70404119D, 7045217, 7050200, 7050412YD, 7050716, 7050717, 7060312PC, 7060412ET, 7060524, 7075312ND, 7075312SD, 7075524, 7075717, 7090524, 7100412NC, 7115520, 71354120D, 7135412AD, 7135417PD, 7135826, 7150453ND, IGNITION
7370A13 IGNITION COIL ASSEMBLY Mariner
Rating:
93

Buy IGNITION COIL ASSEMBLY 7370A13 Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$45.00

27-11-2024
1.5[0.68] pounds
US: Caltric
Caltric 3 Sets of Ignition Coils Compatible with Mercury Outboard 90Hp 90-Hp 90 Hp Engine 1987-1998
Caltric Order Includes: 3 x Ignition Coils || Compatible with Mercury Outboard models: 90HP Engine 1987-1998 / 60HP Engine 1984-1997 / 70HP Engine 1980 / 70HP Engine 1982-1983 / 70HP Engine 1987-1989 / 75HP Engine 1987-1998 / 50HP Engine 1986-1997 / 80HP Engine 1987-1989 || Ignition Coils OEM Part Number: 5288A 2 / 7370A 6 / 7370A 8 / 7370A 2 / 7370A13 / 7370A19 / 832757A4 / 339-832757A / 339-7370A13 || We strongly suggest comparing the posted picture to the unit(s) that needs to be replaced. || Visit the Largest Selection of Powersports & Mowers Aftermarket Parts Online on the Caltric Amazon store - www.amazon.com/caltric
$36.80
 

04-10-2023

-: -
Ignition Coil for Mercury & Mariner Enignes 5288A2 7370A6 7370A8 7370A2 7370A13
Replaces OEM Numbers: || Mercury & Mariner Engines || 5288A2 || 7370A6 || 7370A8 || 7370A2 || 7370A13 || 7370A19 || 832757A4 || 825668, 825668T
$103.99
 

16-08-2023

-: -
The ROP Shop| (Pack of 6) Marine Ignition Coil for Mercruiser 339-7370A13, 3397370A13, 7370A13
The ROP Shop replacement (Pack of 6) Marine Ignition Coil for Mercruiser 339-7370A13, 3397370A13, 7370A13 || Includes - (6) Ignition Coil; comes as shown in the first image || This coil is NOT for models with ignition coils that are thru-bolt mounted (mounting bolt goes through coil body) || Please be sure to check your part or model number to ensure this is the correct ignition coil switch for your unit. Also, please note this may replace multiple part numbers
Number on catalog scheme: 18
 

Mariner entire parts catalog list:

7002201DK 1995
7008237 1987,1988,1989,1990,1991,1992,1993
7020201NC 1988,1989,1990,1991,1992,1993,1994
7020207 1977,1984,1985,1986,1987
70404119D 1989,1990,1991,1992,1993,1994,1995,1996,1997
7045217 1987,1988,1989
7050200 1980,1982,1983,1985,1986
7050412YD 1991,1992,1993,1994,1995,1996
7050716 1986
7050717 1987,1988,1989,1990
7060312PC 1989
7060412ET 1996
7060524 1984,1985,1986,1989,1990
7075312ND 1988,1989
7075312SD 1990,1991,1992,1993
7075524 1984,1985,1986
7075717 1987,1989
7090524 1984,1985,1986,1987,1988
7100412NC 1988,1989,1990,1991,1992,1993
7115520 1980
71354120D 1990,1991
7135412AD 1992,1993,1994,1995
7135417PD 1989
7135826 1986,1987,1988
7150453ND 1988
7150453PD 1989,1990
7150629 1979,1980,1982,1984,1985
7175412PD 1989
7175413AD 1992,1993,1994,1995
7175413PD 1989,1990
7175413YD 1991
7175629 1979,1980,1985,1986,1988
7200412PD 1989,1990
7200620 1980,1982,1983,1984,1985,1986,1988
7220727 1987,1988
7250422PD 1989,1990,1991,1992,1993,1994

Information:


Illustration 1 g01160981
Schematic of the ether injection system
Breathing ether vapors or repeated contact of ether with skin can cause personal injury. Personal injury may occur from failure to adhere to the following procedures.Use ether only in well ventilated areas.Do not smoke while changing ether cylinders.Use ether with care to avoid fires.Do not store replacement ether cylinders in living areas or in the operator's compartment.Do not store ether cylinders in direct sunlight or at temperatures above 49 °C (120 °F).Discard cylinders in a safe place. Do not puncture or burn cylinders.Keep ether cylinders out of the reach of unauthorized personnel.To avoid possible injury, be sure the brakes are applied and all controls are in Hold or Neutral when starting the engine.
Test Step 1. Inspect the Electrical Connectors and the Wiring
Turn the keyswitch to the OFF position.
Illustration 2 g01144470
Left side engine view (typical example) (1) J1/P1 ECM connectors
Illustration 3 g01160988
Components for the ether injection system (typical location) (2) Ether injection solenoid
Thoroughly inspect connectors (1). Inspect the J504/P504 connectors for solenoid (2). Refer to Troubleshooting, "Electrical Connectors - Inspect".
Illustration 4 g01142845
P1 terminals for the ether injection system (P1-18) Solenoid return (ether start valve) (P1-20) Ether injection solenoid
Illustration 5 g01160725
P504 Ether start valve connector (P504-1) Ether start valve (P504-2) Solenoid return (ether start valve)
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the ether injection system.
Check the torque of the allen head screws for the ECM connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and the wiring for abrasion and for pinch points from the ether injection solenoid to the ECM.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The connectors and the wiring appear to be OK. Proceed to Test Step 2.
Not OK - The connectors and/or the wiring are not OK.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Verify that the problem is resolved.STOPTest Step 2. Check for Active Diagnostic CodesNote: Remove the ether canister before you perform this procedure.
Connect Caterpillar Electronic Technician (ET) to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools".
Turn the keyswitch to the ON position.
Proceed to the "Diagnostic Overrides" screen on Cat ET.
Activate the ether injection system. The system will activate for ten seconds.
Monitor the active diagnostic code screen on Cat ET. Wait at least 15 seconds in order for any diagnostic codes to become active. Look for these codes:
2417-05
2417-06Expected Result:No diagnostic codes are active.Results:
No active codes - Neither diagnostic code is active.Repair: The problem may have been caused by a poor electrical connection. Carefully reinspect the connectors and the wiring. Refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
Active 2417-06 code - A 2417-06 code is active. Proceed to Test Step 3.
Active 2417-05 code - A 2417-05 code is active. Proceed to Test Step 4.Test Step 3. Create an Open at the Harness Connector for the Ether Injection Solenoid
Turn the keyswitch to the OFF position.
Disconnect the P504 connectors from the ether injection solenoid.
Turn the keyswitch to the ON position.
Proceed to the "Diagnostic Overrides" screen on Cat ET.
Activate the ether injection system. The system will activate for ten seconds.
Monitor the "Active Diagnostic Codes" screen on Cat ET. Wait at least 15 seconds in order for any diagnostic codes to become active. Look for an active 2417-05 code.
Turn the keyswitch to the OFF position.Expected Result:A 2417-05 code is now active.Results:
OK - A 2417-06 code was active before the connector was disconnected. A 2417-05 code became active after the connector was disconnected.Repair: Temporarily connect a new ether solenoid to the harness, but do not install the new ether solenoid. Verify that there are no active codes for the ether injection system.If there are no active codes for the ether injection system, permanently install the new solenoid. Clear any logged diagnostic codes.STOP
Not OK - A 2417-06 code was active before the connector was disconnected. The 2417-06 code remained active after the connector was disconnected. Do not connect the P504 connector to the ether injection solenoid. Proceed to Test Step 5.Test Step 4. Create a Short at the Connector for the Ether Injection Solenoid
Turn the keyswitch to the OFF position.
Disconnect the P504 connector from the ether injection solenoid.
Install a jumper wire between terminals 1 and 2 of the J504 harness connector.
Turn the keyswitch to the ON position.
Proceed to the "Diagnostic Overrides" screen on Cat ET.
Activate the ether injection system. The system will activate for ten seconds.
Monitor the "Active Diagnostic Codes" screen on Cat ET. Wait at least 15 seconds in order for any diagnostic codes to become active. Look for an active 2417-06 code.


Parts ignition Mariner:

7370A 2
 
7370A 2 IGNITION COIL ASSEMBLY
7070509, 7080629, 7090520, 7115520
44331 4
 
44331 4 IGNITION PLATE
7100412CD, 7100412NC
91882 2
823033
IGNITION COIL
823033 IGNITION COIL
7002201DK, 7002201HB, 7002201SK, 7002201UB, 7003201BK
95242
 
95242 IGNITION COIL
7002201DK, 7002201SK
42968 2
7370A19
 
7370A19 IGNITION COIL
7002201DK, 7016207CD, 7050412YD, 7060412ET, 7135412AD, 7175413AD
43429 2
 
43429 2 IGNITION PLATE
7002201DK, 7135412AD, 7135412ED, 7135412HD, 7150413ED, 7150413HD, 7175413AD, 7175423HD
Back to top