13664 Mariner INSTALLER TOOL, Bearing


13664 INSTALLER TOOL, Bearing Mariner 7006201CD, 7006201HB, 7006201TB, 7008218EW, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 7F08203HF, 7F10203HD, 7F13203UB, 7F15201GD INSTALLER
13664 INSTALLER TOOL, Bearing Mariner
Rating:
83

Buy INSTALLER TOOL, Bearing 13664 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Mariner entire parts catalog list:

7006201CD 1994,1995,1996,1997,1998
7006201HB 1999,2000,2001,2002,2003,2004
7006201TB 2005,2006
7008218EW 1996,1998
7010207HB 1999,2000,2001,2002,2003,2004
7010312DT 1995
7011201TB 2005,2006
7015201LD 2002
7F08203HF 1999
7F10203HD 1999,2000,2001,2002,2003,2004,2005
7F13203UB 2006
7F15201GD 1998

Information:


Table 1
Associated Diagnostic Trouble Codes
J1939 Code CDL Code
108-3 274-3
108-4 274-4
108-13 274-13 Note: Cat ET will report the status for atmospheric pressure as the ambient barometric pressure. The readings for the turbocharger inlet pressure sensor will be approximately the same value that is reported by the atmospheric pressure sensor. The approximate same value readings will occur while the engine is not running. If the readings do not agree, troubleshoot the sensor circuit for the suspect sensor. Refer to Troubleshooting, "Sensor Signal (Analog, Active) - Test".Probable Causes
Associated codes
Boost Leak
Engine operating conditions
Failed exhaust balance valve
High altitude
Obstructed aftercooler
Table 2
Troubleshooting Test Steps Values Results
1. Check for Associated Diagnostic Codes
A. Establish communication between Caterpillar Electronic Technician (ET) and the ECM . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Determine if a code is active or logged.
Associated diagnostic codes
Result: An associated diagnostic code is active or logged.
Troubleshoot the associated code. Refer to Troubleshooting, "Diagnostic Trouble Codes" in order to troubleshoot the associated diagnostic code.
Result: An associated diagnostic code is not active or logged.
Proceed to Test Step 2.
Table 3
DTC with associated derate? Data logged in this histogram? Interpretation
No Yes Derate was probably caused by the exhaust temperature derate.
Yes Yes There may be multiple causes for derate since this exhaust temperature histogram only logs data when it has the largest derate ( another derate may have been active due to a diagnostic trouble code, but a larger exhaust temperature derate was applied).
Yes No Derate was probably not caused by the exhaust temperature derate.
Illustration 1 g02475817
Example of Cat ET screenshot of the histogram. This histogram is populated when the engine system has calculated a condition in which high exhaust temperatures are present. A fault code will not be logged when the system calculates a high exhaust temperature condition, but will activate a de-rate to the engine in order to protect the engine system. This is normal under most circumstances and no additional troubleshooting is necessary.
Note: Information from this histogram is to be used with active and logged diagnostic trouble codes. This histogram is informational if no diagnostic codes are active or logged.
Table 4
Troubleshooting Test Steps Values Results
2. Check for Boost Leakage
A. Apply a light load to the engine and check for boost leakage.
Boost leaks
Result: Boost leakage was found.
Repair the leaks. Return the unit to service.
Result: Boost leakage was not found.
Proceed to Test Step 3.
3. Check the Engine Operating Conditions
A. Check the histogram to determine if the high exhaust temperature was due to normal operation.
When possible, interview the operator. Determine if the engine is being operated under heavy load. Ensure that the engine is being operated at the proper engine speed.
If derates are suspected, reset histogram and return the unit to service. If the histogram repopulates without fault codes, the derate was under normal engine operation.
Normal operation
Result: The code was logged during a heavy load.
Reduce the load on the engine. Return the unit to service.
Result: The code was not logged during a heavy load.
Proceed to Test Step 4.
4. Check the Exhaust Balance Valve
A. An exhaust balance valve that has failed in the closed position can cause high exhaust temperatures, Refer to Troubleshooting, "Exhaust Balance Valve - Test" for the correct troubleshooting procedure.
Failed exhaust balance valve
Result: The exhaust balance valve has failed.
Repair or replace the balance valve. Return the unit to service.
Result: The exhaust balance valve has not failed.
Proceed to Test Step 5.
5. Check the Engine Operating Altitude
A. Check the engine operating altitude.
High altitudes can cause high exhaust temperatures, consider the operational altitude when troubleshooting a high exhaust temperature. High exhaust temperatures are associated with high operational altitudes.
When operating below 5500ft and the ambient temperature is below 30° C (85° F), altitude should not cause a high exhaust temperature derate.
High operational altitudes
Result: The engine was operating at high altitudes.
The high exhaust temperature was due to high altitudes. Return the unit to service.
Result: The engine was not operating at high altitudes.
Proceed to Test Step 6.
6. Check for an Obstructed Aftercooler
A. The intake manifold air temperature can increase if the flow through the aftercooler is obstructed. Check the aftercooler for obstructions or debris. Ensure that the flow of air or coolant through the aftercooler is adequate.
Obstructed aftercooler
Result: The engine aftercooler was obstructed.
Clear any obstructions. Return the unit to service.
Complete the procedure in the order in which the steps are listed.The procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts installer Mariner:

824785A 1
 
824785A 1 INSTALLER TOOL, Bushing And Seal
7006201CD, 7008218EW, 7010312DT, 7F08203HF, 7F15201GD
13663A 1
 
13663A 1 INSTALLER TOOL, Piston Pin
7006201CD, 7008218EW, 7010312DT, 7B25201GF
93843T 1
 
93843T 1 INSTALLER TOOL, Bearing Carrier
7020201HB, 7020201TB, 7F13203UB
Back to top