16250011 Mariner JET, Main (#68)

START BY:a. remove mufflerb. remove fuel injection lines1. Turn off the fuel supply at the fuel tank. 2. Disconnect fuel lines (1) at each end, and remove them from the fuel injection pump housing.3. Disconnect two fuel lines (4). Put plug and caps on all of the fuel line openings.4. Remove the cotter pin and pin (3), and disconnect rod end (2) from the governor. 5. Loosen bolt (5) and nut (6). Move the alternator toward the engine, and remove V-belt (7) from the alternator pulley.6. Remove the bolts that hold guard assembly (9) in position, and remove the guard assembly.7. Remove plug (8) from the timing gear cover. 8. Loosen bolt (10) that holds the fuel pump drive gear to the fuel injection pump camshaft a maximum of one turn.9. Remove three bolts (11).10. Loosen three nuts (12) that hold the fuel injection pump to the timing gear plate. Loosen the nuts until they are even with the end of the studs. 11. Install tool (A) in the timing gear cover. Tighten the forcing screw in tool (A), and loosen the drive gear from the fuel injection pump camshaft.12. Remove tool (A) from the timing gear cover.13. Remove the bolt and washer from the fuel injection pump camshaft.14. Remove three nuts (12), and remove the fuel injection pump housing and governor from the engine. The weight of the fuel injection pump housing and governor is 22 kg (49 lb.).15. Remove the O-ring seals from the fuel injection pump housing.Install Fuel Injection Pump Housing And Governor
1. Install the fuel injection pump housing and governor on tooling (A), or use a suitable vise to hold it.2. Remove the bolts and cover over the timing pin hole in the pump housing.3. Install the washer and bolt (1) that is used to hold the drive gear to the fuel injection pump camshaft.4. Install tool (B) in the hole of the fuel injection pump housing. Use bolt (1), and turn the fuel injection pump camshaft until tool (B) engages in the notch in the camshaft.5. Remove the bolt and washer from the camshaft.6. Remove the fuel injection pump housing and governor from tooling (A). 7. Install O-ring seals (2) and (3) in the fuel injection pump housing. Put clean engine oil on the O-ring seals. 8. Put the fuel injection pump housing and governor in position on the engine, and install three nuts (4).9. Put clean oil on the threads of bolt (1). Install the bolt and washer to hold the drive gear to the fuel injection pump camshaft. Tighten the bolt finger tight only. Bolt (1) must be tight enough to hold the gear clearance (backlash) out of the timing gears when the engine is turned. However, the timing gear must be able to turn on the shaft when the engine is turned to put the No. 1 piston on the top center compression position (TDC). 10. Put No. 1 piston at the top center compression position (TDC) with the following procedure:a. Remove plug (5) from the flywheel housing.b. Turn the crankshaft clockwise (as seen from the front of the engine) until a 3/8"-16 × 2 in. (50.8 mm) bolt can be installed through the timing hole in the flywheel housing and into the hole in the flywheel. c. Remove the valve cover from the valve cover base. Check to see if both rocker arms (6) for the No. 1 piston can be moved backward and forward by hand. The No. 1 piston is at the top center compression position when the bolt is installed in the flywheel, and both rocker arms for No. 1 piston can be moved backward and forward. If both rocker arms cannot be moved, the No. 1 piston is not at the top center compression position. Remove the bolt from the flywheel. Turn the crankshaft clockwise (as seen from the front of the engine) one full turn (360°), and install the bolt again.11. With the timing pin in the notch of the fuel injection pump camshaft and the timing bolt in the flywheel, tighten the bolt which holds the drive gear to the fuel injection pump camshaft to a torque of 175 7 N m (129 5 lb.ft.).12. Check the timing as follows:a. Remove both the timing pin and timing bolt.b. Turn the crankshaft clockwise (as seen from the front of the engine) two full turns, and install the timing pin and bolt again.c. The timing is correct if both the timing pin and timing bolt can be installed at the same time. The timing procedure must be done again if the timing pin and timing bolt cannot be installed at the same time.d. Remove the timing pin and timing bolt when the timing is correct.13. Install the plug in the flywheel housing. 14. Install three bolts (7).15. Put the gasket and cover (8) in position on the fuel injection pump housing, and install the bolts that hold them in place. 16. Install plug (12) in the timing gear cover.17. Put V-belt (11) in position on the alternator pulley. Adjust the belt tension, and tighten bolts (9) and (10).18. Use a belt tension gauge, such as a Borroughs Tool Company part No. BT-33-95 to check the belt tension. The gauge reading should be 534 22 N (120 5 lb.) for a new belt and 400 44 N (90 10 lb.) for a used belt.19. Install guard assembly (13) on the radiator. 20. Put rod end (15) in position, and install the pin (16) and the cotter pin to hold it in place.21. Connect fuel lines (17).22. Install fuel lines (14). Install the clips and bolt to hold fuel lines (14) in position.23. Turn on the fuel supply at the fuel tank.END BY:a. install fuel linesb. install muffler