3796 Mariner JET, MAIN FUEL (.076)


3796 JET, MAIN FUEL (.076) Mariner 70152374D, 7020201HB, 7020201TB, 7090524, 7100412HB, 7100412NC, 7115412TB, 7115520, 71354120D, 7140528, 7140629, 7150453ND, 7150453PD, 7200620, 7225412CD JET
3796 JET, MAIN FUEL (.076) Mariner
Rating:
43

Buy JET, MAIN FUEL (.076) 3796 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

Mariner entire parts catalog list:

70152374D 1994,1995,1996,1997,1998
7020201HB 1999,2000,2001,2002,2003,2004
7020201TB 2005,2006
7090524 1984,1985,1986,1987,1988
7100412HB 1999,2000,2001,2002,2003,2004
7100412NC 1988,1989,1990,1991,1992,1993
7115412TB 2005,2006
7115520 1980
71354120D 1990,1991
7140528 1978,1979
7140629 1979
7150453ND 1988
7150453PD 1989,1990
7200620 1980,1982,1983,1984,1985,1986,1988
7225412CD 1994,1995,1996,1997,1998

Information:

Probable Causes
Event codes
Starting aids
Throttle signal
Turbocharger outlet pressure sensor
Atmospheric pressure sensor
Fuel supply
Air inlet and exhaust system
Accessory equipmentRecommended Actions
Event Codes
Connect the Caterpillar Electronic Technician (ET) and check for an engine derate. Troubleshoot any event codes that are present before continuing with this procedure.Starting Aids
Air Inlet Heater
Verify that the engine has exited "Cold Mode". Verify correct operation of the air inlet heater. For additional information on the air inlet heater, refer to Troubleshooting, "Air Inlet Heater Circuit - Test".Oil Grade Plugs
Make sure that the correct oil grade plug is utilized. Do not program the "Engine Oil Weight" on Cat ET. For additional information on the oil grade plugs, refer to the Operation and Maintenance Manual, "Engine Oil and Filter - Change".Throttle Signal
Monitor "Throttle Position" on Cat ET. Verify that you can achieve full throttle. Refer to Troubleshooting, "Throttle Switch Circuit - Test" for the proper troubleshooting procedure.Turbocharger Outlet Pressure Sensor or Atmospheric Pressure Sensor
Monitor the status of "Fuel Position", "Rated Fuel Limit", and "FRC Fuel Limit" on Cat ET while the engine is operating under full load. These parameters should reflect the information below.
Table 1
"Fuel Position" = "Rated Fuel Limit"    
AND    
"Fuel Position" < "FRC Fuel Limit"    If "Fuel Position" equals "Rated Fuel Limit" and "Fuel Position" is less than "FRC Fuel Limit", the electronics are operating correctly. Otherwise, proceed with the next Step.
Monitor the status of "Boost Pressure" and "Atmospheric Pressure" for normal operation on Cat ET. When the engine is not running, "Boost Pressure" should be 0 kPa (0 psi).
Verify that the turbocharger outlet pressure sensor is operating properly.Fuel Supply
Check the fuel lines for the following problems: restrictions, collapsed lines and pinched lines. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Check the fuel tank for foreign objects which may block the fuel supply.
Check for air in the low pressure fuel supply system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectors
Purge air from the low pressure fuel supply circuit. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.Note: A sight glass in the low pressure supply line is helpful in diagnosing air in the fuel.
Check fuel quality. In temperatures below 0 °C (32 °F), check for solidified fuel (wax). Refer to Special Instruction, SEBD0717, "Diesel Fuels And Your Engine".
Check the fuel pressure during engine cranking. Check the fuel pressure on the outlet side of the fuel filter. Refer to Specifications for correct pressure values. If the fuel pressure is low, replace the fuel filters. If the fuel pressure is still low, check the following items: fuel transfer pump, fuel transfer pump coupling and fuel pressure regulating valve.Air Inlet and Exhaust System
Clean plugged air filters or replace plugged air filters. Refer to the Operation and Maintenance Manual.
Check the air inlet and exhaust system for restrictions and/or leaks. Refer to Testing and Adjusting, "Air Inlet and Exhaust System".Accessory Equipment
Check all accessory equipment for problems that may create excessive load on the engine. Repair any damaged components or replace any damaged components.


Parts jet Mariner:

5317
 
5317 JET, MAIN FUEL (.046)
7002201DK, 7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7015201LD, 70152374D, 7020201HB, 7020201NC, 7020201TB, 7020207, 7075217CD, 7100412CD, 71354120D, 7135412AD, 7135417PD, 7135826, 7200620
5225
 
5225 JET, Main (.054), MAIN FUEL
7002201DK, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY, 7100412C
810742
JET, (.044), PROGRESSION AIR
810742 JET, (.044), PROGRESSION AIR
71354120D, 7135412ED, 7135412HD, 7135412JD, 7175423HD, 7225412HD
815633070
 
815633070 JET, PROGRESSION AIR
7002201DK, 71354120D, 7135412AD, 7225412CD
815633050
JET, (.050) (XR6/MAGNUM III/200)
815633050 JET, (.050) (XR6/MAGNUM III/200)
7002201DK, 7135412AD, 7225412CD, 7225412HD
815633042
 
815633042 JET, Idle Air Vent (.042-TOP)
7135412ED, 7135412HD, 7175423HD, 7225412CD
815633038
JET, (.038) (TOP)
815633038 JET, (.038) (TOP)
7135412ED, 7135412HD, 7135412JD, 7175423HD, 7225412CD
815633054
JET, (.054) (CENTER)
815633054 JET, (.054) (CENTER)
7135412JD, 7225412CD, 7225412HD
Back to top