97776M Mariner KILL SWITCH (LEAD WIRES ARE 19" - 2 MALE TERMINALS)


97776M KILL SWITCH (LEAD WIRES ARE 19" - 2 MALE TERMINALS) Mariner 7010209, 7015529, 7025207NW, 7025207PW, 7030301 KILL
97776M KILL SWITCH (LEAD WIRES ARE 19" - 2 MALE TERMINALS) Mariner
Rating:
63

Buy KILL SWITCH (LEAD WIRES ARE 19" - 2 MALE TERMINALS) 97776M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Mariner entire parts catalog list:

7010209 1979,1983,1984,1985,1986
7015529 1979
7025207NW 1988
7025207PW 1989,1990,1991,1992,1993
7030301 1981

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
8149-5
Aftertreatment DEF Doser Ready Status : Current Below Normal 3583-5
Switch Panel #1 : Current Below Normal
8149-6
Aftertreatment DEF Doser Ready Status : Current Above Normal 3583-6
Switch Panel #1 : Current Above Normal
Table 2
Troubleshooting Steps Value Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the dosing cabinet service port connector.
B. Determine if the code is logged or active.
Codes
Result: A -5 code is present.
Proceed to Test Step 2.
Result: A -6 code is present.
Proceed to Test Step 3.
2. Check the Wiring for an Open Circuit
A. Verify that the harness connector is free of debris, corrosion, and secured.
B. Remove the electrical power from the Selective Catalyst Reduction (SCR) Controller.
C. Disconnect connector PR-C674 from the aftertreatment wiring harness.
D. Install a jumper wire between the terminals E and F of the aftertreatment harness connector PR-C674. The aftertreatment harness is replaced with a short circuit.
E. Restore the electrical power to the ECM.
F. Connect Cat ET to the dosing cabinet service port connector.
G. Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.
Note: Wait at least 30 seconds in order for the diagnostic code to be-come active.
Create a Short
Result: A -5 code became active.
The SCR controller did not detect the jumper wire. There is an open circuit between the aftertreatment wiring harness connector PR-C674 and the SCR ECM connector J1 PR-C5. There might be a problem with a connector.
Repair: Repair or replace the connectors or wiring.
Proceed to Test Step 4.
Result: A -6 code became active.
The SCR Controller detected the jumper wire. The wiring between the Selective Catalyst Reduction Controller and the PR-C674 connector is OK. There is a problem with the Aftertreatment Doser Ready Status input circuit between the PR-C674 connector and the customer connection.
Repair: Repair or replace the wiring harness between the PR-C674 connector and the customer connection.
Proceed to Test Step 4.
3. Check the Wiring to the Engine Harness for a Short Circuit
A. Turn keyswitch to OFF.
B. Disconnect connector PR-C674 from the aftertreatment wiring harness.
C. Turn keyswitch to ON.
D. Connect Cat ET using the dosing cabinet service port connector.
E. Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.
Short Circuit
Result: A -5 code became active.
The wiring between the Selective Catalyst Reduction Controller and the PR-C674 connector is OK. There is a problem with the Aftertreatment Doser Ready Status input circuit between the PR-C674 connector and the customer connection.
Repair: Repair or replace the wiring harness between the PR-C674 connector and the customer connection.
Proceed to Test Step 4.
Result: A -6 code became active.
There is a short circuit in the wiring between the aftertreatment wiring harness connector PR-C674 and the SCR System ECM connector J1PR-C5. There may be a problem with a connector.
Repair: Repair or replace the connectors or wiring.
Proceed to Test Step 4.
4. Check for Codes
A. Connect Cat ET to the dosing cabinet service port connector.
B. Determine if the code is logged or active.
Codes
Result: No codes are present.
Return to service.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts kill Mariner:

97682M
 
97682M KILL SWITCH ASS'Y
7010209, 7015529, 7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7030205, 7040202, 7040716, 7055524, 7060522
97755M
 
97755M KILL SWITCH ASSEMBLY - REMOTE
7008204, 7008208, 7008226, 7010209, 7015529, 7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7040202, 7040206, 7040207PW, 7040706, 7040716
97757M
 
97757M KILL SWITCH (1 RING/1 MALE TERMINAL - 24")
7010209, 7015529, 7025208CW, 7030301, 7040202, 7040207PW, 7040208PW, 7040716, 7048321
97777M
 
97777M KILL SWITCH (LEAD WIRE ARE 3" - 2 MALE TERMINALS)
7010209, 7015529, 7025200, 7025207NW, 7025207PW, 7025500, 7030301
97774M
 
97774M KILL SWITCH, MOTOR MOUNT
7025200, 7025500, 7026226, 7030205, 7030301
92611M
 
92611M KILL SWITCH, MOTOR MOUNT
7025200, 7025207NW, 7025500
92612M
 
92612M KILL SWITCH ASS'Y
7025207NW, 7040507
Back to top