76264 Mariner LATCH, FRONT COVER ATTACHING


76264 LATCH, FRONT COVER ATTACHING Mariner 7050716, 7060312PC, 7060524, 7070509, 7070520, 7150629, 7175629, 7200620, 7250422PD LATCH
76264 LATCH, FRONT COVER ATTACHING Mariner
Rating:
53

Buy LATCH, FRONT COVER ATTACHING 76264 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 34
 

Mariner entire parts catalog list:

7050716 1986
7060312PC 1989
7060524 1984,1985,1986,1989,1990
7070509 1979
7070520 1980,1982,1983
7150629 1979,1980,1982,1984,1985
7175629 1979,1980,1985,1986,1988
7200620 1980,1982,1983,1984,1985,1986,1988
7250422PD 1989,1990,1991,1992,1993,1994

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     5P-4758     Retaining Ring Pliers As     1    
C     1P-2854     Spanner Wrench     1    
D     8T-9149     Guide     1    
8T-9144 Ring Installer     1    
E     8T-9148     Seal Driver     1    
F     8T-9159     Seal Guide     1    
G     8B-7556     Adapter     1    
8B-7555 Adapter     2    
0S-1575 Bolt     2    
5H-1504 Hard Washer     2    
8B-7552 Bolt     1    
1B-4206 Nut     1    
3H-0465 Push-Puller Plate     5    
8B-7548 Puller     1    
8B-7550 Puller Leg     2    
1B-4207 Full Nut     1    
H     9S-3263     Thread Lock Compound     1    
J     6V-1541     Quick Cure Primer     1    
K     5P-0960     Grease Cartridge     1    
Illustration 1 g00381352
Raise the temperature of bearing cone (29), bearing cup (27), bearing ring (28), bearing cup (30), and bearing cone (31). Install bearing cone (29), bearing cup (27), bearing ring (28), bearing cup (30), and bearing cone (31) .
Illustration 2 g00305963
Apply Tooling (H) to the threads of spanner nut (25). Use Tooling (C) to tighten spanner nut (25). Tighten spanner nut (25) to a torque of 1.1 - 1.5 N m (10 - 13 lb in).
Measure the drive shaft and bearing assembly in order to determine the thickness of the shim that will be used under the shaft seal cover. Refer to the appropriate Testing and Adjusting manual for your machine.
Measure the center pin, the spacer, the barrel, and the control plate in order to determine the proper size for the spacer that should be used for the assembly. Refer to the appropriate Testing and Adjusting manual for your machine.
Illustration 3 g00305851
Put the drive shaft and piston assembly (16) in position on a section of suitable pipe or on suitable blocks. Put center pin (23), washer (24), and retainer plate (20) in position on the drive shaft and piston assembly (16) .
Illustration 4 g00305853
Apply Tooling (J) to the threads of screws (22) and allow screws (22) to dry. ApplyTooling (H) to the threads of screws (22) and install screws (22) loosely in order to hold the retainer plate to the drive shaft assembly. Put three pistons (19) in position in order to align the retainer plate. Tighten screws (22). Tighten screws (22) to a torque of 9 2 N m (7 1 lb ft). Remove three pistons (19) from the assembly.
Illustration 5 g00305854
Illustration 6 g00305857
Improper installation of parts can prevent proper operation or cause damage to the system.Make sure that all piston rings are installed with the marks toward the flat end of the piston.
The piston rings are spherical in shape. Install the piston rings with Marks (X) toward the flat end of piston (19). Use Tooling (D), and install the upper piston ring. Install the lower piston ring by using Tooling (D) with Marks (X) toward the flat end of piston (19). Repeat this procedure for the remaining pistons.


Parts latch Mariner:

38279
 
38279 LATCH, CONTROL CABLE FASTENING - ANCHOR BRACKET
7002201DK, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115473JD, 7115520, 7115528, 7115529, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 7135473GD, 71354
39483
 
39483 LATCH, THROTTLE CONTROL LEVER (THROTTLE CABLE)
7002201DK, 70404119D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 7135826, 7150413ED, 7150413HD, 7150423JD, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175
87608
 
87608 LATCH, Cowl
7135826, 7150453ND, 7150629, 7175629, 7200620, 7220727
46785A 5
 
46785A 5 LATCH ASSEMBLY, Cowl
7050717, 7060312PC, 7135826, 7150453ND, 7150629, 7175629, 7200620, 7220727
18168A 1
12242A 1
 
12242A 1 LATCH
71354120D, 7135417PD, 7135826, 7150453ND, 7150453PD, 7175412PD, 7175413PD, 7175629, 7200412PD, 7200620, 7220727, 7250422PD
98889
 
98889 LATCH
7002201DK, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 70404119D, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7050717, 7055207GD, 7055207HB,
Back to top