84352M Mariner EXTENSION, LEAD


84352M EXTENSION, LEAD Mariner 7008204, 7008208, 7008218EW, 7008226, 7008238, 7008248, 7008425, 7010209, 7015529, 7020201, 7025200, 7025207PW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7040202, 7040206, 7040207, 7040207PW, 7040208, 7040328, 7040507, 7040716, 7 EXTENSION
84352M EXTENSION, LEAD Mariner
Rating:
38

Buy EXTENSION, LEAD 84352M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Mariner entire parts catalog list:

7008204 1984,1985,1986
7008208 1978
7008218EW 1996,1998
7008226 1986
7008238 1978
7008248 1978
7008425 1985,1989,1990,1991,1992,1993,1994,1995,1997
7010209 1979,1983,1984,1985,1986
7015529 1979
7020201 1981
7025200 1980
7025207PW 1989,1990,1991,1992,1993
7025500 1980
7026226 1986,1988
7028207 1977
7028527 1977
7030200 1980
7030205 1985,1986,1987,1988,1989,1990
7030301 1981
7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040207 1977
7040207PW 1989,1990,1991,1992,1993
7040208 1978
7040328 1978,1980
7040507 1987
7040716 1986
7055524 1984,1985
7060522 1982

Information:


Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Illustration 1 g02178677
Thoroughly clean the area around fuel manifold (4).
Disconnect harness assembly (6) from fuel pressure sensor (5).
Disconnect plastic tube assembly (1) from the fuel pressure relief valve on fuel manifold (4). Immediately cap the open port in fuel manifold (4) with a new cap. Immediately plug the open end of plastic tube assembly (1) with a new plug.
Remove bolt (2) and bolts (3). Remove fuel injection line support bracket (7).
Remove fuel manifold (4) from the cylinder head. Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that all ports on the fuel manifold are capped. Ensure that the fuel manifold is externally clean and free from damage. Note: Do not install a fuel manifold that has not been capped. All caps must be left in place until the fuel injection lines or the fuel pressure relief valve are installed.
Illustration 2 g02178677
Position fuel manifold (4) onto the cylinder head. Install bolts (3) to fuel manifold (4) finger tight.
Position fuel injection line support bracket (7) onto the fuel rail. Install remaining bolt (3). Install bolt (2) for injection line support bracket (7) finger tight.
Install a new set of seals and a new set of fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install" for the correct procedure.
Tighten bolts (3) to a torque of 22 N m (195 lb in).
Tighten bolts (2) to a torque of 10 N m (89 lb in).
Remove the plug from plastic tube assembly (1). Connect plastic tube assembly (1) to the fuel pressure relief valve.
Connect harness assembly (6) to fuel pressure sensor (5).
Replace the filters for primary fuel system. Refer to Operation and Maintenance Manual, "Fuel System Primary (Water Separator) Element - Replace" for the correct procedure.
Replace the filters for secondary fuel system. Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for more information. End By:
Install the mounting bracket and the inlet air control (NRS Induction Mixer). Refer to Disassembly and Assembly, "Inlet Air Control (NRS Induction Mixer) - Install" for the correct procedure.


Parts extension Mariner:

83194M
 
83194M EXTENSION (LONG SHAFT)...
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
83206M
 
83206M EXTENSION, LONG SHAFT
7028207, 7028527
81614M
 
81614M EXTENSION,
7028207, 7028527
83814M
84223M
 
84223M EXTENSION KIT, LONG SHAFT
7008208, 7008238, 7008248, 7008305
84229M
 
84229M EXTENSION KIT, ULTRA LONG SHAFT
7008208, 7008218EW, 7008238, 7008248, 7008305, 7008425
84230M
 
84230M EXTENSION KIT, SUPER ULTRA LONG SHAFT
7008208, 7008218EW, 7008238, 7008248, 7008305, 7008425
99060M
 
99060M EXTENSION, LEAD
7008204, 7008208, 7008226, 7010209, 7015529, 7040207PW
Back to top