54920A 1 Mariner LENS ASSEMBLY, FUEL GAUGE...


54920A 1 LENS ASSEMBLY, FUEL GAUGE... Mariner 7008204, 7008208, 7008226, 7008238, 7008247, 7008248, 7015207, 7015307, 7015327, 7020201, 7025200, 7025207NW, 7025500, 7028207, 7028527, 7030200, 7040202, 7040207, 7040208, 7040328, 7040507, 7040716, 7048207, 7048227, 7048321, 7060507, 7060522, 70605 LENS
54920A 1 LENS ASSEMBLY, FUEL GAUGE... Mariner
Rating:
73

Buy LENS ASSEMBLY, FUEL GAUGE... 54920A 1 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Mariner entire parts catalog list:

7008204 1984,1985,1986
7008208 1978
7008226 1986
7008238 1978
7008247 1977,1987
7008248 1978
7015207 1977
7015307 1977
7015327 1987
7020201 1981
7025200 1980
7025207NW 1988
7025500 1980
7028207 1977
7028527 1977
7030200 1980
7040202 1982,1985,1986
7040207 1977
7040208 1978
7040328 1978,1980
7040507 1987
7040716 1986
7048207 1977
7048227 1977
7048321 1981
7060507 1977
7060522 1982
7060528 1978
7070509 1979
7080508 1978,1979
7090529 1979
7115528 1978
7115529 1979
7140528 1978,1979
7140629 1979

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
B 276-1216 Injector Pipe Nut Tool 1
C 367-2771 Wrench 1
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Note: The following procedure should be adopted in order to install the fuel injection lines when the electronic unit injectors or the fuel manifold have not been removed. If the electronic unit injectors or the fuel manifold have been removed, refer to Disassembly and Assembly, "Electronic Unit Injector - Install" and Disassembly and Assembly, "Fuel Manifold - Install" for more information.
Illustration 1 g02481080
Remove plugs from fuel manifold (5) and fuel injection pump (23).
Remove the caps from new fuel injection line (24).
Position fuel injection line (24) onto fuel injection pump (23) and fuel manifold (5). Loosely install nuts for the fuel injection line onto the fuel manifold and the fuel injection pump.
Install bolt (20) to the tube clip finger tight.
Install bolt (21) and spacer (22) to the tube clip finger tight.
Use Tooling (C) to tighten the nuts on fuel injection line (24) to a torque of 40 N m (30 lb ft).
Tighten bolt (20) and bolt (21) to a torque of 10 N m (89 lb in). Note: Ensure that fuel injection lines do not contact any other engine component.
Illustration 2 g02625818
Position bracket (18) and the harness assembly onto the fuel injection pump.
Install bolt (16) and bolt (19) (not shown) to bracket (18). Tighten the bolt to a torque of 9 N m (80 lb in).
Connect harness assembly (14) to coolant temperature sensor (12). Slide locking tab (13) into the locked position.
Connect harness assembly (17) to fuel pressure sensor.
Install new cable strap (15). Note: Ensure that the cable strap meets Original Equipment Manufactures (OEM) specification.
Illustration 3 g02481216
Illustration 4 g02481081
Illustration 5 g02625722
Install new seals (3) to the electronic unit injector and cylinder head (6). Ensure that the flange on the seal is flush with the cylinder head.
Remove the caps from the port of the electronic unit injector and from the appropriate port in fuel manifold (5).
Loosely connect the nuts at both ends of fuel injection line (1) and fuel injection line (4), to the electronic unit injector and to the appropriate port in fuel manifold (5). Ensure that the ends of the fuel injection line are correctly seated in the electronic unit injector and in the fuel manifold.
Install bracket (10) and isolator (11). Position isolator (9) and clamp plate (8).
Use a suitable tool in order to install clamp plate (8) to bracket (10).
Install bolt (2) finger tight.
Use Tooling (B) to tighten the nuts on fuel injection line (1) and fuel injection line (4) to a torque of 55 N m (41 lb ft). Ensure that the dust seal is seated correctly against the seal.
Tighten bolt (2) to a torque of 10 N m (89 lb in).
Follow Step 13 through Step 20 in order to install the remaining fuel injection lines.
Turn the fuel supply to the ON position.
Turn the battery disconnect switch to the ON position.
Remove the air from the fuel system. Refer to Operations and Maintenance Manual, "Fuel System - Prime" for the correct procedure. End By:
Install the inlet air control (NRS Induction Mixer). Refer to Disassembly and Assembly, "Inlet Air Control (NRS Induction Mixer) - Install" for the correct procedure.
Install secondary fuel filter assembly. Refer to Disassembly and Assembly, "Fuel Filter Base (Single Secondary Fuel Filter) - Remove and Install" for the correct procedure.
Install water separator and fuel filter (Primary). Refer to Disassembly and Assembly, "Water Separator and Fuel Filter (Primary) - Remove and Install" for the correct procedure.
Install crankcase breather canister and plastic tube assemblies. Refer to Disassembly and Assembly, "Crankcase Breather - Remove" for the correct procedure.


Parts lens Mariner:

80269M
 
80269M LENS, INDICATOR
7015207, 7015307, 7015327, 7020201, 7025200, 7025500, 7028207, 7028527, 7030200, 7048207, 7048227, 7048321, 7060507, 7060522, 7060528
80724M
 
80724M LENS, CHOKE LAMP
7028207, 7028527
Back to top