11950M Mariner LEVER, FREE ACCEL.


11950M LEVER, FREE ACCEL. Mariner 7008204, 7008208, 7008226 LEVER
11950M LEVER, FREE ACCEL. Mariner
Rating:
38

Buy LEVER, FREE ACCEL. 11950M Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$113.74
 

08-03-2022

-: -
InvisibleMask P#:2010-DODGE-RAM 11950M Clear Bra Paint Protection Film Kit for a Dodge RAM TRX 1500 Coverage Includes a Hood Fender Mirror Kit (3M Scotchgard Film)
3M Scotchgard film specifically cut for a 2010 DODGE RAM TRX 1500 || Coverage includes pre-cut paint protection film listed in the title. || Comes with a professional squeegee, squirt bottles, instruction DVD, knife, microfiber cloth and door edge guards || Protect your vehicles paint finish with our computer cut clear-coated paint protection films. InvisibleMask clear bra kits are precisely pre-cut to fit the contours of your car. || InvisibleMask products will protect your vehicle from bugs, dirt, scratches, nicks, road salt, sand and road debris and will cause no damage to your OEM paint if removed years later.
Number on catalog scheme: 3
 

Compatible models:

Mariner entire parts catalog list:

7008204 1984,1985,1986
7008208 1978
7008226 1986

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
B 9U-7222 Camshaft Bearing Pilot 1
8M-8778 Taperlock Stud
1/2 - 13 by 1 9/16 inch 1
C 9U-7210 Puller Plate 1 Start By:
Remove the camshaft.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01159745
Remove the No. 7 camshaft bearing (rear). Work from the rear of the engine to the front of the engine.
Install the small end of Tooling (B) in camshaft bearing (1).
Position Tooling (C) over Tooling (A). Install Tooling (A) through the cylinder head on Tooling (B). Note: Tooling (C) is installed on the outside of the cylinder head. Tooling (C) is required in order to remove all the camshaft bearings from the cylinder head.
Use Tooling (A) to remove camshaft bearing (1) from the cylinder head.
Remove Tooling (B) from Tooling (A) and remove the camshaft bearing. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
B 9U-7222 Camshaft Bearing Pilot 1
8M-8778 Taperlock Stud
1/2 - 13 by 1 9/16 inch 1
C 9U-7210 Puller Plate 1
D 9U-7223 Alignment Bushing 1
E 9U-7213 Backup Plate 1
0S-1621 Bolt
1/2 - 13 by 1 inch 1
F 9U-7214 Spacer Plate 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01159754
Install the No. 7 camshaft bearing (rear), as follows:
Insert the large end of Tooling (B) into the No. 7 camshaft bore.
Position Tooling (C) over Tooling (A). Install Tooling (A) through the cylinder head on Tooling (B).
Position camshaft bearing (1) on Tooling (B). Install Tooling (E) on Tooling (B). Note: Refer to Specifications, "Cylinder Head" for appropriate information for the orientation of the camshaft bearings in the cylinder head.
Use Tooling (A) in order to pull camshaft bearing (1) into the camshaft bore. Note: When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed.
Illustration 3 g01159756
Install the No. 6 through No. 2 camshaft bearings, as follows:
Insert the large end of Tooling (B) into the camshaft bore. Note: Use Tooling (D) to align Tooling (A) and Tooling (B) with the camshaft bearing bores. Install Tooling (D) in the inside diameter of any installed camshaft bearing between Tooling (A) and Tooling (B).
Install Tooling (A) on Tooling (B). Position camshaft bearing (1) on Tooling (B). Install Tooling (E) on Tooling (B). Note: Refer to Specifications, "Cylinder Head" for appropriate information for the location and the orientation of the camshaft bearings in the cylinder head.
Use Tooling (A) in order to pull camshaft bearing (1) into the camshaft bore. Note: When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed.
Illustration 4 g01159758
Install the No. 1 camshaft bearing (front), as follows:
Insert the large end of Tooling (B) into the No. 1 camshaft bore. Assemble Tooling (A) and Tooling (D) on Tooling (B).
Position camshaft bearing (1) on Tooling (B). Install Tooling (E) and Tooling (F) on Tooling (B). Note: Refer to Specifications, "Cylinder Head" for appropriate information for the location and the orientation of the camshaft bearings in the cylinder head.Note: Tooling (F) is used to seat the No. 1 camshaft bearing to the correct depth in the camshaft bore.
Use Tooling (A) in order to pull the No. 1 camshaft bearing into the No. 1 camshaft bore. When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed. End By:
Install the camshaft.


Parts lever Mariner:

91660M
 
91660M LEVER, CLAMP
7004201, 7005201, 7005207, 7008204, 7008208, 7008226
83302M
 
83302M LEVER CHOKE ASS'Y
7008208, 7008238, 7008248
11408M
 
11408M LEVER, CLAMP
7008204, 7008208, 7008226
83278M
 
83278M LEVER, CLAMP
7008208, 7008238, 7008248
11512M
LEVER, SHIFT ROD
11512M LEVER, SHIFT ROD
7008204, 7008208, 7008226
11558M
LEVER, THROTTLE
11558M LEVER, THROTTLE
7008204, 7008208, 7008226
11503M
 
11503M LEVER, MAGNETO CONTROL
7008204, 7008208, 7008226
83267M
 
83267M LEVER, MAGNETO CONTROL
7008208, 7008218EW, 7008238, 7008248, 7008305, 7008425
Back to top