83049M Mariner LEVER, TILT...


83049M LEVER, TILT... Mariner 7008208, 7008238, 7008247, 7008248 LEVER
83049M LEVER, TILT... Mariner
Rating:
53

Buy LEVER, TILT... 83049M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 27
 

Compatible models:

Mariner entire parts catalog list:

7008208 1978
7008238 1978
7008247 1977,1987
7008248 1978

Information:


This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Note: Valve lash is measured between the rocker arm and the valve bridge. All measurements and adjustments must be made with the engine stopped and the valves fully closed.Valve Lash Check
An adjustment is NOT NECESSARY if the measurement of the valve lash is in the acceptable range. Check the valve lash while the engine is stopped. The range is specified in Table 1.
Illustration 1 g00363480
Valve lash
Table 1
Valve Lash    
Valves     Acceptable Range for Valve Lash    
Inlet    
0.38 0.08 mm (0.015 0.003 inch)    
Exhaust    
0.76 .08 mm (0.030 0.003 inch)    If the measurement is not within this range adjustment is necessary. Refer to Testing And Adjusting, "Valve Lash Adjustment".Valve Lash Adjustment
Illustration 2 g00363481
Valve adjustment
Illustration 3 g00797249
(A) Inlet valves (B) Exhaust valves
Table 2
Valve Lash    
Valves     Dimension of the Gauge    
Inlet    
0.38 mm (0.015 inch)    
Exhaust    
0.76 mm (0.030 inch)    Adjust the valve lash while the engine is stopped. Use the following procedure in order to adjust the valves:
Put the No. 1 piston at the top center position.Note: See Testing and Adjusting, "Finding Top Center Position for the No. 1 Piston" for further details.
With No. 1 piston at the top center position of the compression stroke, an adjustment can be made to the valves.Before any adjustments are made, lightly tap each rocker arm at the top of the adjustment screw. Use a soft mallet to ensure that the lifter roller seats against the camshaft's base circle.
Make an adjustment to the valve lash on the inlet valves for cylinders 1, 3, 4, 6, 7 and 12.
Loosen valve adjustment locknut (3) .
Place the appropriate feeler gauge (5) between the inlet rocker arm and the inlet valve bridge. Turn inlet adjustment screw (4) while valve adjustment locknut (3) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (3) while valve adjustment screw (4) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Make an adjustment to the valve lash on the exhaust valves for cylinders 1, 4, 5, 8, 9, and 12.
Loosen valve adjustment locknut (1) .
Place the appropriate feeler gauge (5) between the exhaust rocker arm and the exhaust valve bridge. Turn exhaust adjustment screw (2) while valve adjustment locknut (1) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (1) while valve adjustment screw (2) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Remove the timing bolt, and turn the flywheel by 360 degrees in the direction of engine rotation. This will position the No. 7 piston at the top center on the compression stroke. Install the timing bolt in the flywheel.
Make an adjustment to the valve lash on the inlet valves 2, 5, 8, 9, 10, and 11.
Loosen valve adjustment locknut (3) .
Place the appropriate feeler gauge (5) between the inlet rocker arm and the inlet valve bridge. Turn inlet adjustment screw (4) while valve adjustment locknut (3) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (3) while valve adjustment screw (4) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Make an adjustment to the valve lash on the exhaust valves 2, 3, 6, 7, 10, and 11.
Loosen valve adjustment locknut (1) .
Place the appropriate feeler gauge (5) between the exhaust rocker arm and the exhaust valve bridge. Turn exhaust adjustment screw (2) while valve adjustment locknut (1) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (1) while valve adjustment screw (2) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Remove the timing bolt from the flywheel after all valve lash adjustments have been made.


Parts lever Mariner:

80523M
 
80523M LEVER
7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
82611M
81063M
81069M
 
81069M LEVER, SHIFT ROD...
7008238, 7008247
80526M
11663M
 
11663M LEVER, MAGNETO CONTROL
7008204, 7008208, 7008226
11665M
 
11665M LEVER, MAGNETO CONTROL
7008204, 7008208, 7008226
84664M
 
84664M LEVER, TILT
7008208, 7008218EW, 7008238, 7008248, 7008305, 7008425
Back to top