19609 Mariner LINK ROD (PORT)


19609 LINK ROD (PORT) Mariner 7050717, 7060312PC LINK
19609 LINK ROD (PORT) Mariner
Rating:
63

Buy LINK ROD (PORT) 19609 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Compatible models:

Mariner entire parts catalog list:

Information:

1. Remove the plug from location (1). Install tool (A) in the hole with the square end down. Move the governor control the the "ON" position until the rack stops against tool (A). The racks are now in center (zero) position. 2. Disconnect lines (2) from the fuel injection pumps. Remove washers (3). Put caps on all fuel openings.3. Remove bushing (4) with tool (B). 4. Remove fuel injection pump with tool (C).
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
5. Disassemble the fuel injection pump. Remove ring (6). Make a separation of bonnet (5) from the plunger and barrel assembly (7).
Be careful when the injection pumps are disassembled. Do not cause damage to the surface on the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
6. Remove the gear segment, washer and spring from the barrel.7. Remove the ring, spring, collar and valve from the barrel. 8. Remove spacer (8).Install Fuel Injection Pumps
Make sure the fuel racks are in the center (zero) position before the fuel injection pumps are installed.1. Install plunger (10) and gear segment (11), washer (5) and spring (9) in position on barrel (4). Put check valve assembly (7), spring (3) and collar (8) in position in bonnet (6). Connect bonnet (6) and barrel (4) together with ring (2). Keep seal (1) with bonnet for use at installation. 2. Put spacer (13) into position in the pump housing bore. Make sure the correct spacer is with each pump.3. Put the space in gear segment (11) in alignment with the groove in barrel (4).4. Put the injection pump straight down into the housing bore so the space in gear segment (11) is in alignment with pin (12) and the groove in barrel (4) is in alignment with dowel (14). Use tool (C) to install the pump. 5. Install seal (1) and bushing (15) in the pump housing bore. If the pump is in the correct position, bushing (15) will turn into the threads of the pump housing with the fingers until it is even with the housing. Tighten bushing (15) to a torque of 205 14 N m (150 to 10 lb.ft.) with tool (B).6. Install washers (16).7. Connect the fuel lines to the injection pumps and tighten fuel line nuts to a torque of 40 7 N m (30 5 lb.ft.) with tool (D).8. Check for correct installation of the injection pumps with the engine stopped. See INJECTION PUMP INSTALLATION in TESTING AND ADJUSTING.
If one or more of the injection pumps have been installed wrong, damage to the engine is possible if cautions are not taken when the engine is first started. Make preparation to close off the air intake to stop the engine if necessary.
9. Remove the timing pin [Tool (A)] and install the plug in the injection pump housing.


Parts link Mariner:

65799
 
65799 LINK, LOCKING LEVER TO COVER
7050716, 7060312PC, 7060524, 7070509, 7070520, 7080508, 7080629, 7085507, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
60283A 1
 
60283A 1 LINK ASSEMBLY, SHIFT SHAFT AND ANCHOR BRACKET
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
94275
 
94275 LINK, SOLENOID TO SOLENOID
7045217, 7050200, 7050716, 7060312PC, 7060524, 7070520, 7080629, 7090520, 7115520, 7150629, 7200620, 7250422PD
19608
 
19608 LINK ROD (STARBOARD)
7050717, 7060312PC
17432A 6
 
17432A 6 LINK ROD ASSEMBLY
7050717, 7060312PC
17432A 5
 
17432A 5 LINK ROD ASSEMBLY
7050717, 7060312PC
19385 21
 
19385 21 LINK NON-POWER TRIM
7050717, 7060312PC
Back to top