84413M Mariner MANIFOLD, INTAKE


84413M MANIFOLD, INTAKE Mariner 7060507, 7060528 MANIFOLD
84413M MANIFOLD, INTAKE Mariner
Rating:
103

Buy MANIFOLD, INTAKE 84413M Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$23.09
 

01-10-2017

Bosch: Bosch
Bosch 84413M 7/8-Inch Diameter 15/32-Inch Cut Carbide Tipped Beading Router Bit 1/2-Inch Shank With Ball Bearing
Recommended for use with a routing table||All bits must be inserted in the full length of the collet. Be sure to use only router bits and accessories specifically designed for your router
Number on catalog scheme: 18
 

Compatible models:

7060507   7060528   Mariner

Mariner entire parts catalog list:

7060507 1977
7060528 1978

Information:


Illustration 1 g01207158
Schematic for the Cat Data Link
Test Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 2 g01167488
Location of the J1/P1 ECM connectors (typical engine view)
(1) J1/P1 ECM connectors
Illustration 3 g01207179
Location of the engine interface connector and the service tool connector (typical engine view)
(2) Engine interface connector
(3) Service tool connector
Thoroughly inspect connectors (1), (2), and (3). Refer to Troubleshooting, "Electrical Connectors - Inspect".
Illustration 4 g01207225
P1 terminals that are associated with the Cat Data Link
(P1-8) Cat Data Link +
(P1-9) Cat Data Link −
Illustration 5 g01207319
Terminals at the engine interface connector that are associated with the Cat Data Link
(13) Cat Data Link +
(14) Cat Data Link −
Illustration 6 g01207229
Terminals at the service tool connector that are associated with the Cat Data Link
(D) Cat Data Link +
(E) Cat Data Link −
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the Cat Data Link.
Check the allen head screw on each ECM connector for the proper torque. Also, check the allen head screw on the engine interface connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values. Expected Result:All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and the connectors appear to be OK. Proceed to Test Step 2.
Not OK - The connectors and/or the wiring are not OK.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the original problem is resolved.STOPTest Step 2. Check the Data Link for a Short Circuit
Disconnect the J1 connector.
Disconnect Cat ET from the service tool connector.
Measure the resistance between the points that are listed in Table 1. Be sure to wiggle the wires in the harnesses as you make each resistance measurement.
Table 1
Resistance Measurements for the Cat Data Link
Connector and Terminal Terminal
P1-8 (Cat Data Link +) All of the other terminals on the P1 connector
Ground stud
P1-9 (Cat Data Link -) All of the other terminals on the P1 connector
Ground stud Expected Result:Each check of the resistance indicates an open circuit.Results:
OK - Each check of the resistance indicates an open circuit. The data link is not shorted to another wire in the harness. Proceed to Test Step 3.
Not OK - At least one check of the resistance does not indicate an open circuit.Repair: There is a short circuit in the harness or in a connector. Repair the connectors and/or the wiring. Replace parts, if necessary.STOPTest Step 3. Check for an Open Circuit
Fabricate a jumper wire that is long enough to short circuit two terminals at the service tool connector. Crimp connector sockets to each end of the jumper wire.
Install the jumper wire between terminals D (Cat Data Link +) and E (Cat Data Link −) at the service tool connector.
At the J1 ECM connector, measure the resistance between P1-8 (Cat Data Link +) and P1-9 (Cat Data Link −). Expected Result:The resistance check indicates that continuity exists for the circuit.Results:
OK - The resistance check indicates that continuity exists.Repair: Perform the following procedure:
Connect the J1/P1 connectors. Connect Cat ET to the service tool connector.
Check the Cat Data Link for proper operation. If the Data Link does not operate correctly, there may be a problem with the ECM. Replace the ECM. Refer to Troubleshooting, "Replacing the ECM" for information that is related to ECM replacement.STOP
Not OK - The resistance check did not indicate that continuity exists in the circuit. There is an open circuit or excessive resistance in the harness.Repair: There may be a problem with a connector. Repair the wiring and/or the connectors. Replace parts, if necessary.STOP


Parts manifold Mariner:

81271M
 
81271M MANIFOLD, INTAKE
7048207, 7048227, 7060507, 7060528
92632M
 
92632M MANIFOLD, INTAKE
7055524, 7060507, 7060522
Back to top