880582T05 Mariner MANIFOLD ASSEMBLY, Intake


880582T05 MANIFOLD ASSEMBLY, Intake Mariner 7200V13IR, 7200V23ID, 7200V23IR, 7225V13ID, 7225V13IR, 7225V13TF, 7225V13UB, 7225V13ZB, 7225V23ID, 7225V23IR, 7225V24IB, 7225V24ID, 7250V13ID, 7250V23IR, 7275V23ID, 7275V23IR, 7300V23ID MANIFOLD
880582T05 MANIFOLD ASSEMBLY, Intake Mariner
Rating:
53

Buy MANIFOLD ASSEMBLY, Intake 880582T05 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

Mariner entire parts catalog list:

7200V13IR 2006
7200V23ID 2006
7200V23IR 2006,2007
7225V13ID 2006
7225V13IR 2006,2007
7225V13TF 2005
7225V13UB 2006
7225V13ZB 2006
7225V23ID 2006,2007
7225V23IR 2006,2007
7225V24IB 2007
7225V24ID 2006
7250V13ID 2006,2007
7250V23IR 2006
7275V23ID 2006
7275V23IR 2006,2007
7300V23ID 2006

Information:

1. Loosen four bolts (1) evenly and remove rocker shaft assembly (2). 2. Put identification on push rods (3) and valve bridges (4) for installation purposes.3. Remove push rods (3) and valve bridges (4).Install Rocker Shaft Assembly
1. Install push rods (1) in their respective locations.2. Put clean engine oil on the bridge dowels. Install valve bridges (2) in their respective locations.3. Push straight down on the top contact surface of valve bridge (2) with a force of 1 to 10 lb. (4 to 45 N). Turn the adjustment screw clockwise until contact is made with the valve stem. Turn the adjustment screw 20° to 30° more to keep bridge (2) straight on the dowel. Hold the adjustment screw in this position and tighten the locknut to a torque of 22 3 lb.ft. (28 4 N m). 4. Put the rocker shaft assembly (7) in position on the cylinder head. Make sure the rocker arms and push rods are in alignment before the bolts that hold the rocker shafts in position are tightened.5. Put clean engine oil on the threads of bolts (3) through (6). Tighten bolts (3) through (6) in number sequence to a torque of 200 20 lb.ft. (270 25 N m). Tighten bolts again in number sequence to a torque of 330 15 lb.ft. (447 20 N m). Tighten the bolts again in number sequence to a torque of 330 15 lb.ft. (447 20 N m).6. Make an adjustment of the valves to have a clearance of .015 in. (0.38 mm) for intake and .030 in. (0.76 mm) for exhaust. See VALVE CLEARANCE SETTING in TESTING AND ADJUSTING.end by:a) install valve cover basesDisassemble Rocker Shaft Assembly
start by: a) remove rocker shaft assembly 1. Remove retainer (1) from the end of the shaft.2. Remove the washers and rocker arm (2). 3. Use tool (A) to remove the pin that holds bracket (3) to the rocker arm shaft.4. Remove bracket (3), rocker arm (4) and the spring.5. Remove the remainder of the rocker arms. The center brackets do not have pins.Assemble Rocker Shaft Assembly
Make sure all parts of the rocker shaft assembly are clean before assembly.1. Put clean engine oil on shaft (3).2. Install the center springs, rocker arms and bracket. 3. Install spring (1), rocker arm (4) and bracket (2).4. Put tape around the shaft on each side of bracket (2) as shown. Put the hole in bracket (2) in alignment with the hole in shaft (3). Put a mark on each piece of tape in alignment with the hole in bracket (2).5. Install pin (5) until it is extended .50 .04 in. (12.7 1.0 mm) above the surface of bracket (2). Make sure pin (5) is in alignment with the marks on the tape before pin is installed. Remove the tape. 6. Install rocker arm (6), washers (7) and retainer (8). Install enough washers until the end play on each end of the shaft is .012 - .055 in. (0.30 - 1.40 mm).end by: a) install rocker shaft assembly


Parts manifold Mariner:

896166A01
MANIFOLD KIT, Trim
896166A01 MANIFOLD KIT, Trim
7200V13IR, 7200V23ID, 7200V23IR, 7225V13ID, 7225V13IR, 7225V13TF, 7225V13UB, 7225V13ZB, 7225V23ID, 7225V23IR, 7225V24IB, 7225V24ID, 7250V13ID, 7250V23IR, 7275V23ID, 7275V23IR, 7300V23ID
Back to top