813430A 1 Mariner MEMORY PISTON KIT


813430A 1 MEMORY PISTON KIT Mariner 70404119D, 7050302ED, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY, 7A30302L MEMORY
813430A 1 MEMORY PISTON KIT Mariner
Rating:
48

Buy MEMORY PISTON KIT 813430A 1 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

Mariner entire parts catalog list:

70404119D 1989,1990,1991,1992,1993,1994,1995,1996,1997
7050302ED 1996,1997
7055207GD 1998
7055207HB 1999,2000,2001,2002,2003,2004
7055207TF 2005,2006
7060412ET 1996
7075217CD 1994,1995,1996,1997,1998
7075217HD 1999,2000,2001,2002,2003,2004
7075217TD 2005
7075217UD 2006
70752L7TF 2005
70752L7UF 2006
7075317TB 2005
7075317UB 2006
7075412TB 2005
7075412UB 2006
7075412UY 2006
7090412TB 2005
7090412TD 2005
7090412TY 2005
7090412UB 2006
7090412UY 2006
7A30302LB 2002,2003,2004,2005
7A40302UD 2006
7A40312UZ 2006
7A41452IZ 2006
7A51412ZZ 2006
7A51452IZ 2006
7A60412ZZ 2006
7A60452IZ 2006
7E41412ZB 2006
7E51412ZB 2006
7E51413VZ 2010
7E60412ZB 2006
7E60413VZ 2010
7E60452IZ 2007
7E60452ZB 2006
7F30203HD 1999,2000,2001
7F30203LB 2002,2003,2004,2005
7F40203UD 2006
7F40213UZ 2006
7F40452KD 2001
7F40452LB 2002
7F41452KD 2001
7F50352HD 1999,2000

Information:


For initial start-up of a new or rebuilt engine, and for start-up of an engine that has been serviced, make provision to shut the engine off should an overspeed occur. This may be accomplished by shutting off the fuel supply to the engine.
Do not start the engine or move any of the controls if there is a "DO NOT OPERATE" warning tag or similar warning tag attached to the start switch or to the controls.Ensure that no one will be endangered before the engine is started and when the engine is started.If the engine has not been operated for several weeks, fuel may have drained from the fuel filters and air may have entered the fuel filter housing. When fuel filters have been replaced, some air is left in the fuel filter housing. Prime the fuel system in these situations. See this Operation and Maintenance Manual, "Fuel System - Prime".Perform the procedures that are described in this Operation and Maintenance Manual, "Before Starting Engine".
Ensure that the barring device is disengaged.
Illustration 1 g00994262
Ensure that "LOCAL SPEED CONTROL" (3) is in the low idle position.
Turn "FUEL CONTROL ON/OFF" switch (2) to the "ON" position.
The engine must be prelubed before the crankshaft is rotated. Damage can result if the crankshaft is rotated on dry bearing surfaces.
Turn "PRELUBE/START" switch (1) to the "PRELUBE" position. Allow the prelube pump to operate until "PRELUBE" indicator (4) illuminates.When the "PRELUBE" indicator illuminates, the oil pressure will be approximately 9 kPa (1.3 psi).Note: Marine vessels are generally equipped with an electric fuel priming pump.
Activate the fuel priming pump. Operate the fuel priming pump until fuel pressure is indicated on the fuel pressure gauge.
Start the engine at low idle rpm with no load. Turn "PRELUBE/START" switch (2) to the "START" position. When 180 to 200 rpm is achieved, release the "PRELUBE/START" switch.The starting motors will disengage when the engine reaches 170 rpm.Note: If the engine does not start after ten seconds, turn the "FUEL CONTROL ON/OFF" switch to the "OFF" position. Purge the cylinders. See this Operation and Maintenance Manual, "Before Starting Engine" (Operation Section).
Immediately after engine start-up, ensure that oil pressure and fuel pressure are indicated on the gauges. Allow the engine to idle for three to five minutes. The engine speed should stabilize at low idle rpm. Check all of the pressure gauges. Inspect the engine for leaks and listen for unusual noises. While the engine is at low idle and the lube oil has warmed up, check the lube oil. Maintain the oil level between the "ADD" and "FULL" marks on the oil level gauge. When all systems are normal, the rpm may be increased.Ensure that the oil pressure and the fuel pressure are in the normal ranges. After the engine has started and the warm-up is complete, the engine can be operated at low rpm and low load. The engine will reach normal operating temperature faster if the engine is operated at low rpm and with a low power demand. This procedure is more effective than idling the engine with no load. The engine should reach normal operating temperature in a few minutes.


Parts memory Mariner:

810776
 
810776 MEMORY PISTON KIT (SEE NOTE)
70404119D, 7050302ED, 7050412YD, 7050717, 7060312PC, 7060412ET, 7075217CD, 7075312SD, 7100412CD, 7100412NC
810776A 1
 
810776A 1 MEMORY PISTON ASSEMBLY
70404119D, 7050302ED, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7075D73UY, 7075D73ZY, 7090412TB, 7090412TD, 7090412TY, 7090412U
Back to top