64484 Mariner NUT, JAM - ADJUSTING SCREW


64484 NUT, JAM - ADJUSTING SCREW Mariner 7080508, 7080629, 7085507 NUT
64484 NUT, JAM - ADJUSTING SCREW Mariner
Rating:
8

Buy NUT, JAM - ADJUSTING SCREW 64484 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Compatible models:

Information:


Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Disconnect batteries before performance of any service work.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
This Special Instruction provides the information that is necessary to install the 199-3409 Solenoid Assembly to the governor assembly. 199-3409 Solenoid Assembly
Table 1
Parts that are included in 199-3409 Solenoid Assembly
Refer to Illustration 1 for the location of parts.    
Item     Description     Qty    
1     Retainer clip     1    
2     Washer for shaft     1    
3     Spacer     2    
4     Bolt for cover     3    
5     Solenoid     1    
6     Solenoid to shaft link     1    
7     Bolt for lever     1    
8     O-ring Seal     1    
9     Cover     1    
10     Stop lever     1    
11     Guide bolt     3    
12     Formed seal     1    
13     Nut for solenoid     3    
14     Silicone lube     1    
Illustration 1 g00831460
(1) Retainer clip (2) Washer for shaft (3) Spacer (4) Bolt for cover (5) Solenoid (6) Solenoid to shaft link (7) Bolt for lever (8) O-ring seal (9) Cover (10) Stop Lever (11) Guide boltProcedure to Install the 199-3409 Solenoid Assembly
Remove the following items: former solenoid, stop lever and O-ring. Clean the installation surface.
Coat O-ring seal (8) with silicone lube and install the O-ring seal in the counterbore around the shaft.
Install the stop lever (10) and bolt for lever (7). Hold the lever in the position and torque the bolt to 8 N m (70 lb in).
Install the formed rubber seal (not shown) by pressing the round form into the cast hole in the governor housing.
Install solenoid (5). Torque the nuts for guide bolt (11) to 12 N m (106 lb in).Note: The solenoid bracket must be flush with the governor.
Coat the chamfered side of the spacer (3) with lube and install the spacer on the shaft.Note: Retract the solenoid plunger in order to gain clearance.
Coat the solenoid to shaft link (6) with lube. Install the solenoid to shaft link (6) on the shaft and the solenoid.
Coat the chamfered side of spacer (3) with lube and install spacer (3) on the shaft. Add the washer for shaft (2) and retainer clip (1) .
Check solenoid operation before attaching the cover.
Coat the edges of cover (9) with silicone lube.
Install cover (9) with bolts (4) finger tight. Press the cover inward toward the solenoid. Then, tighten the bolts.


Parts nut Mariner:

28903
 
28903 NUT
7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008226, 7008238, 7008247, 7008248, 7008305, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7040202, 70402
45076
 
45076 NUT, VOLTAGE REGULATOR TERMINAL
7002201DK, 7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 70152374D, 7016207CD, 7020201HB, 7020201NC, 7020201TB, 7020207, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 70404119D, 7041203GB, 7045217, 705
36069
 
36069 NUT, TILT STOP LEVER SCREW
7020207, 7045217, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7135417PD, 7135826, 7140528, 7140629, 7150453ND, 7150453PD, 7150629, 7175412PD, 717562
68219
 
68219 NUT, LOCK-THROTTLE ROD
7002201DK, 7020207, 70404119D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060507, 7060524, 7060528, 7070509, 7070520, 7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115473JD, 7115520, 7115528, 7115529, 71354120D, 7135412AD, 7135
24656
 
24656 NUT, BRACKET TO THRU-BOLT
7050200, 7050716, 7060507, 7070509, 7070520, 7080508, 7080629, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
56041
 
56041 NUT, TILT TUBE FASTENING
7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7075312ND, 7075312SD, 7075524, 7075717, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7100412NC, 7115520, 7115528, 7115529, 71354120D, 7135417PD, 7135826, 7140528, 7140
52901
 
52901 NUT, FLYWHEEL
7002201DK, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115473JD, 7115520, 7115528, 7115529, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 7135473GD, 71354
20013
 
20013 NUT, RETAINER SCREW
7075524, 7080508, 7080629, 7085507
Back to top