82258M Mariner O-RING, PULL WIRE


82258M O-RING, PULL WIRE Mariner 7010209, 7015529, 7020201, 7025200, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030320, 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716, 7055524, 7060507, 7060522, 7060528, 7F10203HD, 7F13203UB, 7F15201GD O
82258M O-RING, PULL WIRE Mariner
Rating:
83

Buy O-RING, PULL WIRE 82258M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 25
 

Mariner entire parts catalog list:

7010209 1979,1983,1984,1985,1986
7015529 1979
7020201 1981
7025200 1980
7025500 1980
7026226 1986,1988
7028207 1977
7028527 1977
7030200 1980
7030205 1985,1986,1987,1988,1989,1990
7030320 1980,1990,1992
7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040207 1977
7040208 1978
7040328 1978,1980
7040507 1987
7040706 1986,1990,1992
7040716 1986
7055524 1984,1985
7060507 1977
7060522 1982
7060528 1978
7F10203HD 1999,2000,2001,2002,2003,2004,2005
7F13203UB 2006
7F15201GD 1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2322 Puller Assembly 1
5P-4170 Step Plate 1
B 5P-0944 Puller Group 1
5P-0941 Extractor 1
5P-0939 Extractor 1 Start By:
Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove".
Remove the timing gear cover. Refer to Disassembly and Assembly, "Timing Gear Cover - Remove and Install".
Remove the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install".
Remove the pistons and the connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Remove".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00790969
Typical example
Check each bearing cap (1) for the location on the engine. Each bearing cap has an arrow which points toward the front of the engine and a number which gives the location of that bearing cap. Keep each bearing with the correct bearing cap.
Remove the bearing caps No. 2 through No. 6. Remove thrust plates from No. 4 upper bearing.
Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft. Remove No. 1 and No. 7 main bearing caps. Remove the crankshaft. The weight of the crankshaft is approximately 148 kg (326 lb).
Be careful not to damage the crankshaft journals when removing the crankshaft.
Illustration 2 g00790992
Remove crankshaft gear (2) with Tooling (A).
Remove the dowel and the pin with Tooling (B).
Put an identification mark on the upper half of the main bearing for proper location in the cylinder block. Remove main bearing upper halves.
Check the condition of the main bearings and crankshaft. Refer to Guideline for Reusable Parts, SEBF8009 and Visual Inspection of Crankshafts, SEBF8043.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
C 8T-5096 Dial Indicator Group 1
D - LOCTITE Graphite-50 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01424064
Install pin (5) in crankshaft (7).Maximum protrusion of pin (5) from the face of crankshaft (7) ... 6.4 0.5 mm (0.25 0.02 inch)
Install dowel (6) in crankshaft (7).The protrusion of dowel (6) from crankshaft (7) face. ... 4.1 0.5 mm (0.16 0.02 inch)
Illustration 4 g01424067
Raise the temperature of crankshaft gear (2) to a maximum temperature of 232 °C (450 °F). Install gear (2) on the crankshaft with groove (3) in alignment with the dowel.Note: Gear (2) must be installed on the crankshaft with the "V"timing mark toward the outside.
Clean the block and the upper main bearings.Note: Install the main bearings dry when clearance checks are made. Put clean engine oil on the upper main bearings and journals of the crankshaft.
Install the upper bearings in the cylinder block. Ensure that the tab in each bearing is in alignment with the notch in the cylinder block.
Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and place the crankshaft into position in the block. The weight of the crankshaft is approximately 180 kg (400 lb).
Install the crankshaft with the


Parts o Mariner:

80350M
 
80350M O-RING
7002207, 7005207, 7005227, 7008238, 7008247, 7015207, 7015327, 7025207PW, 7025500, 7026226, 7028207, 7028527, 7030205, 7030301, 7030320
82274M
 
82274M O-RING, PIVOT SHAFT BUSHING
7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320
84821M
 
84821M O-RING (LONG AND ULTRA LONG SHAFT)
7020201, 7025200, 7025208CW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320
84757M
 
84757M O-RING
7028527, 7030200, 7030205, 7030301, 7030320
45254
 
45254 O-RING, VALVE TO MANIFOLD
7045217, 7050200, 7050716, 7060312PC, 7060507, 7060524, 7060528, 7070520, 7080629, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
45253
 
45253 O-RING, VALVE TO MANIFOLD
7045217, 7050200, 7050716, 7060312PC, 7060507, 7060524, 7060528, 7070520, 7080629, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
17111M
 
17111M O-RING
7040206
17110M
 
17110M O-RING
7040206
Back to top