99325 Mariner SEAL,GEAR HOUSING


99325 SEAL,GEAR HOUSING Mariner 7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 70152374D, 7016207CD, 7020201HB, 7020201NC, 7020201TB, 7020207, 7B25201GF, 7F08203HF, 7F08261DF, 7F10203HD, 7F13203UB, 7F15201GD SEAL
99325 SEAL,GEAR HOUSING Mariner
Rating:
63

Buy SEAL,GEAR HOUSING 99325 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 55
 

Mariner entire parts catalog list:

7006201CD 1994,1995,1996,1997,1998
7006201HB 1999,2000,2001,2002,2003,2004
7006201TB 2005,2006
7008218EW 1996,1998
7008237 1987,1988,1989,1990,1991,1992,1993
7010207HB 1999,2000,2001,2002,2003,2004
7010312DT 1995
7011201TB 2005,2006
7015201LD 2002
70152374D 1994,1995,1996,1997,1998
7016207CD 1994,1995,1996
7020201HB 1999,2000,2001,2002,2003,2004
7020201NC 1988,1989,1990,1991,1992,1993,1994
7020201TB 2005,2006
7020207 1977,1984,1985,1986,1987
7B25201GF 1998
7F08203HF 1999
7F08261DF 1995,1996,1997,1998
7F10203HD 1999,2000,2001,2002,2003,2004,2005
7F13203UB 2006
7F15201GD 1998

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     9S-9082     Engine Turning Tool     1    Start By:
Remove the engine oil pump.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01139029
Use Tooling (A) to turn the crankshaft until the connecting rod bearing caps are accessible.
Check connecting rod (3) and connecting rod caps (1) for identification and for the location.
Remove connecting rod cap bolts (2) and connecting rod cap (1) from connecting rod (3). Remove the lower half of connecting rod bearing (5) from connecting rod cap (1) .Note: This engine has fractured connecting rods. Fractured connecting rods must be handled with care. Use a soft faced hammer in order to tap the connecting rod cap, if necessary.Note: Do not place the fractured faces of the connecting rod cap on any surface. The connecting rod cap must be laid flat on the side in order to prevent damage to the fractured faces of the connecting rod cap.
Push connecting rod (3) away from the crankshaft. Remove the upper half of connecting rod bearing (4) from connecting rod (3) .Note: Do not damage the fractured faces of the connecting rod. Place a suitable protective cap on the ends of the connecting rod in order to prevent damage to the fractured faces of the connecting rod.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The joint between the connecting rod and the connecting rod cap is produced by fracturing. The connecting rod assembly must be handled with care in order to avoid damage to the mating surfaces. The connecting rod assembly must be replaced if any damage occurs to the mating surfaces. New connecting rod assemblies come with the connecting rod caps bolted on the connecting rod.Use only a soft faced hammer to tap the connecting rod cap when separating the connecting rod cap from the connecting rod.Failure to use a soft faced hammer may result in damage to the fractured surfaces of the connecting rod assembly.
Use Tooling (A) to turn the crankshaft until the connecting rod bearing cap is accessible.
Illustration 2 g01139029
Note: Install the connecting rod bearings dry when clearance checks are performed. Apply clean engine oil to the connecting rod bearings for final assembly.
Remove the protective caps from the end of the connecting rod and install the upper half of connecting rod bearing (4). Ensure that the bearing tab engages with the slot in connecting rod (3) .
Pull the piston and connecting rod assembly onto the crankshaft.
Install the lower half of connecting rod bearing (5) into connecting rod cap (1). Ensure that the bearing tab engages with the slot in connecting rod cap (1) .Note: Do not place the fractured faces of the connecting rod cap on any surface. The connecting rod cap must be laid flat on the side in order to prevent damage to the fractured faces of the connecting rod cap.Note: Ensure that the number on the connecting rod cap matches the number on the connecting rod. Make sure that both of the numbers are located on the same side.
Install connecting rod cap (1) and connecting rod cap bolts (2) .
Check the bearing clearance. Refer to Disassembly and Assembly, "Bearing Clearance - Check".
Tighten connecting rod cap bolts (2) to a torque of 50 5 N m (37 3 lb ft).
Place an index mark on each connecting rod cap bolt (2). Tighten each bolt for an additional 90 5 degrees (1/4 turn).
Use Tooling (A) to rotate the crankshaft in order to ensure that the crankshaft turns freely.End By: Install the engine oil pump.


Parts seal Mariner:

15067A 1
43507
83271M
 
83271M SEAL
7008208, 7008218EW, 7008238, 7008248, 7008425
42102 1
 
42102 1 SEAL
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 7016207CD, 7F08203HF, 7F08261DF, 7F10203HD, 7F13203UB, 7F15201GD
78862A 2
 
78862A 2 SEAL KIT
7002201DK, 7008237, 71354120D, 7135412AD, 7135417PD, 7175412PD, 7200412PD, 7250422PD, 7F08261DF
825771
SEAL
825771 SEAL
7F08203HF, 7F08261DF
850837
SEAL
850837 SEAL
7F10203HD, 7F13203UB, 7F15201GD
852432
SEAL
852432 SEAL
7F10203HD, 7F13203UB, 7F15201GD
Back to top