10112050 Mariner OWNERS MANUAL, 20/25 (2-Stroke)

Priority ENGINE COOLING NEEDS TO BE INCREASED ON CERTAIN PM-565B COLD PLANERS
1380 7272 PI30103 This Program must be administered as soon as possible. When reporting the repair, use "PI30103" as the Part number and "7751" as the Group Number, "56" as the Warranty Claim Description Code and "T" as the SIMS Description Code. Exception: If the repair is done after failure, use "PI30103" as the Part Number, "7751" as the Group Number, "96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code.
The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.
COMPLETION DATE
TERMINATION DATE
June 30, 2001 December 31, 2001PROBLEM
In certain operating conditions the engine coolant may overheat in certain PM-565B Cold Planers. The cooling capacity will be increased by installing a new air inlet grill and larger coolant flow restrictors.
AFFECTED PRODUCT
Model Identification Number
PM-565B 8GS1-185, 187, 190, 191PARTS NEEDED
Dealers will need to order parts for this Program.
Quantity Part Number Description
1 1857210 Plate AssemblyACTION REQUIRED
See the attached procedure.
OWNER NOTIFICATION
U.S. and Canadian owners will receive the attached Owner Notification.
SERVICE CLAIM ALLOWANCES
Caterpillar Dealer Suggested Customer Suggested
Parts
(D/N) Labor Hrs.
(Sell) Parts Labor Hrs. Parts
(C/L) Labor Hrs.
(Sell)
100% 4 0 0 0 0
This is a 4-hour job.
U.S. and Canadian Dealers Only - Eligible dealers may enter a Type 2 SIMS Report.PARTS DISPOSITION
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
MAKE EVERY EFFORT TO COMPLETE THIS PROGRAM AS SOON AS POSSIBLE.
Attach. (1-Owner Notification)
(2-Rework Procedure)
COPY OF OWNER NOTIFICATION FOR U.S. AND CANADIAN OWNERS
XYZ Corporation
3240 Arrow Drive
Anywhere, YZ 99999
PRIORITY - ENGINE COOLING NEEDS TO BE INCREASED ON CERTAIN PM-565B COLD PLANERS
MODELS INVOLVED - PM-565B COLD PLANERS
Dear Caterpillar Product Owner:
In certain operating conditions the engine coolant may overheat in the products listed below. The cooling capacity will be increased by installing a new air inlet grill and larger coolant flow restrictors.
Contact your local Caterpillar dealer immediately to schedule this service. The dealer will advise you of the time required to complete this service. Please refer the dealer to their Service Letter dated December 6, 2000 when scheduling this service. You will not be charged for the service performed.
We regret the inconvenience this may cause you, but urge you to have this service performed as soon as possible to prevent unscheduled downtime.
Caterpillar Inc.
Identification #(s)
Attached to December 6, 2000 Service Letter
REWORK PROCEDURE
Raise the machine to it's full height and install the leg supports.
Drain the radiator into a suitable container. Radiator capacity is 21 gallons. Save as much of the coolant as possible, it can be reused.
Disconnect and remove the two top tank tube assemblies (1G8577 and 1G8578) from the radiator top tank and the thermostat housing outlets.
At the engine end of each of the two top tank tubes, drill out the orifice plates from 1 inch diameter to 1-3/8 inch diameter. Deburr the new orifices and clean the tube assemblies.
Reinstall the reworked tube assemblies in the reverse order from which they were removed.
At the bottom radiator tube(1G8618), re-align the tube with the water pump housing inlet on the engine. The gap between the tube and the housing should be between 1/4 to 1/2 inch. If the hose interfers with this alignment, trim 1-1/8 inch from it's length.
Check th gap between the bottom tube assembly and bottom radiator outlet. Adjust the gap to less than 1/2 inch. The hose does not need to be shortened.
As you retighten the clamps on the bottom tank tube, maintain a straight alignment of all connections.
Refill the radiator with coolant.
Remove the air inlet cover assembly(134-3215) and replace it with the new air inlet cover assembly(185-7210). It will be neccesary