10212060 OWNERS MANUAL Mariner
7A40302UD, 7A40312UZ, 7F40203UD, 7F40213UZ
OWNERS
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$186.89
09-07-2023
1.2[0.54] Pounds
-: -
Ametric® 10.2120.60 Metric Polyurethane Timing Belt, Steel Cords, 10 mm Pitch, T10 Tooth Profile, 2120 mm Long, 60 mm Wide, 212 Teeth, 2.5 mm Depth of Tooth, 3.5 mm Tooth Face Length, 4.5 mm Belt Thinkness, (1-040)
1-040-10.2120.60 Ametirc® Part Number || T10 Tooth Profile || 10 mm Pitch || 2120 mm Long || 60 mm Wide
1-040-10.2120.60 Ametirc® Part Number || T10 Tooth Profile || 10 mm Pitch || 2120 mm Long || 60 mm Wide
Number on catalog scheme: -
Mariner entire parts catalog list:
- SERVICE-SUPPORT MATERIAL » 10212060
- SERVICE-SUPPORT MATERIAL » 10212060
- SERVICE-SUPPORT MATERIAL » 10212060
- SERVICE-SUPPORT MATERIAL » 10212060
Information:
start by:a) remove stub shaft *b) remove drive shaft (lower) *c) remove radiator, hydraulic oil cooler and air conditioning core ** Operation location is in POWER TRAIN DISASSEMBLY AND ASSEMBLY section.* If lift facilities are available, the engine and torque converter can be removed straight out of the top of the machine without removal of the radiator, hydraulic oil cooler and air conditioning core.**1. Remove mufflers. Remove all platforms, sheet metal and side panels that are necessary for removal of the engine. Drain transmission and engine.2. Remove crankcase guards. 3. Disconnect hose (3) from the torque converter sequence and pressure control valve. Remove bolt (1), then disconnect cable (2) from the torque converter sequence and pressure control valve. On all hoses or tubes that are removed or disconnected put caps or covers on them to keep out foreign material. Put identification on them for installation purposes. 4. Disconnect two hydraulic hoses (4) from the transmission oil pump. 5. Disconnect wire assembly (5). 6. Remove cotter pin and pin (7), then disconnect governor control linkage (6). 7. Remove baffle (9) and air baffle section (8). 8. Disconnect air conditioning line (10). 9. Disconnect lines (11) and (13). Remove water hose (12). 10. Disconnect wires (14) and (15) from the starter. 11. Disconnect hoses (16) and push them away from the engine. 12. Fasten tool (A) and a hoist to the engine and torque converter. Remove bolts (17) from support assembly on flywheel housing. 13. Remove bolts (18) from support assembly on opposite side of flywheel housing. 14. Remove four bolts (19) from the engine front support. Make a final check to be sure that all removals and disconnections have been made from the engine. 15. Remove engine and torque converter (20) as a unit with tool (A) and a hoist. Weight of the unit is 8000 lb. (3600 kg).Install Engine And Torque Converter
1. Fasten tool (A) and a hoist to the engine and torque converter (1). Put the engine and torque converter in position on the machine frame. 2. Install four bolts (2) on the engine front support. 3. Install rear support (4) and the two bolts (3) that hold it. 4. Install rear support (5) with the two bolts (6) that hold it. 5. Connect hoses (7) with the flanges and bolts that hold them. 6. Connect the wires (8) and (9) that were disconnected from the starter. 7. Connect lines (10) and (11). Install water hose (12). 8. Connect air conditioning hose (13) to the air conditioning compressor.9. See AIR CONDITIONING AND HEATING, CHARGING THE SYSTEM, Form No. SENR7454. 10. Install air baffle section (14). Install baffle (15). 11. Connect the governor control linkage (16) to the governor with the pin (17) and cotter pin that holds it. 12. Connect wire assembly (18). 13. Connect two hydraulic hoses (19) to the transmission oil pump. 14. Connect hose (20) to the torque converter sequence and pressure control valve. Connect cable (21) to the valve with the bolt that holds it.15. Install crankcase guards. Install all side panels, supports, sheet metal and all platforms that were removed for engine removal.16. Fill transmission and engine with oil to their correct levels. See LUBRICATION AND MAINTENANCE GUIDE.end by:a) install radiator, hydraulic oil cooler and air conditioning coreb) install drive shaft (lower) *c) install stub shaft ** Operation location is in POWER TRAIN DISASSEMBLY AND ASSEMBLY section. Operation location is in POWER TRAIN DISASSEMBLY AND ASSEMBLY section.
1. Fasten tool (A) and a hoist to the engine and torque converter (1). Put the engine and torque converter in position on the machine frame. 2. Install four bolts (2) on the engine front support. 3. Install rear support (4) and the two bolts (3) that hold it. 4. Install rear support (5) with the two bolts (6) that hold it. 5. Connect hoses (7) with the flanges and bolts that hold them. 6. Connect the wires (8) and (9) that were disconnected from the starter. 7. Connect lines (10) and (11). Install water hose (12). 8. Connect air conditioning hose (13) to the air conditioning compressor.9. See AIR CONDITIONING AND HEATING, CHARGING THE SYSTEM, Form No. SENR7454. 10. Install air baffle section (14). Install baffle (15). 11. Connect the governor control linkage (16) to the governor with the pin (17) and cotter pin that holds it. 12. Connect wire assembly (18). 13. Connect two hydraulic hoses (19) to the transmission oil pump. 14. Connect hose (20) to the torque converter sequence and pressure control valve. Connect cable (21) to the valve with the bolt that holds it.15. Install crankcase guards. Install all side panels, supports, sheet metal and all platforms that were removed for engine removal.16. Fill transmission and engine with oil to their correct levels. See LUBRICATION AND MAINTENANCE GUIDE.end by:a) install radiator, hydraulic oil cooler and air conditioning coreb) install drive shaft (lower) *c) install stub shaft ** Operation location is in POWER TRAIN DISASSEMBLY AND ASSEMBLY section. Operation location is in POWER TRAIN DISASSEMBLY AND ASSEMBLY section.
Parts owners Mariner:
10212J60
10212D60