36571 Mariner PILOT WASHER


36571 PILOT WASHER Mariner 7031203GD, 7031207CD, 70432037D, 7055207GD, 7135412ED, 7135412HD, 7135473GD, 7135473HD, 7150413ED, 7150413HD, 7175423HD, 7200473GD, 7200473HD, 7225412CD, 7225413DD, 7B25201GF, 7F25201GD, 7F41452KD, 7F50352HD, 7F50412DD PILOT
36571 PILOT WASHER Mariner
Rating:
38

Buy PILOT WASHER 36571 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Mariner entire parts catalog list:

7031203GD 1998,1999
7031207CD 1994,1995,1996,1997,1998
70432037D 1997,1998
7055207GD 1998
7135412ED 1996,1997,1998
7135412HD 1999
7135473GD 1998
7135473HD 1999
7150413ED 1996,1997,1998
7150413HD 1999
7175423HD 1999
7200473GD 1998
7200473HD 1999
7225412CD 1994,1995,1996,1997,1998
7225413DD 1995,1996,1997,1998
7B25201GF 1998
7F25201GD 1998
7F41452KD 2001
7F50352HD 1999,2000
7F50412DD 1995,1996,1997,1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6193 Valve Spring Compressor 1
416-0288 Adapter 1
416-0292 Head 1
B(1) 9U-6198 Crankshaft Turning Tool 1
B(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove" for the correct procedure.Note: Either Tooling (B) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted to remove the valve springs when the cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install" for the procedure to remove the valve springs from a cylinder head that has been removed from the engine.Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed. Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder bore.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Plug the apertures for the push rods in the cylinder head to prevent the entry of loose parts into the engine.
Illustration 1 g03423086
Follow Step 1.a through Step 1.f to remove the harness assembly for the electronic unit injectors.
Use a deep socket to remove connections (1) from electronic unit injectors (2).
Cut cable straps (4) and remove the remaining sections of the cable straps from the cylinder head.
Disconnect plug (6) from harness assembly (3).
Remove bolt (5) from harness assembly (3).
Withdraw harness assembly (3) from the cylinder head.
Repeat Step 1.a through Step 2 to remove the remaining harness assemblies.
Illustration 2 g01978814
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Follow Step 2.a through Step 2.d to position the appropriate piston at top dead center.
Illustration 3 g03423087
Install Tooling (A) in position on the cylinder head to compress a valve spring (10) for the appropriate cylinder.Note: Ensure that the electronic unit injector label code (12) is not damaged when Tooling (A) is compressed.
Use Tooling (A) to compress valve spring (10) and open the valve slightly.Note: Do not compress the spring so that valve spring retainer (9) touches valve stem seal (11).
Use Tooling (B) to rotate the crankshaft carefully, until the piston touches the valve.Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent valve stems.
Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the piston is at the top dead center position. The valve is now held in a position that allows the valve spring to be safely removed.Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of each cylinder. If all valve springs require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 6, 2 with 5 and 3 with 4. Ensure that all the valve springs are installed before changing from one pair of cylinders to another pair of cylinders.
Do not turn the crankshaft while the valve springs are removed.
Apply sufficient pressure to Tooling (A) to allow removal of valve keepers (8).Note: Do not compress the spring so that valve spring retainer (9) touches valve stem seal (11).
Remove valve spring retainer (9).
Slowly release pressure on Tooling (A).
Remove valve spring retainer (9) and remove valve spring (10).
If n


Parts pilot Mariner:

827671A 1
 
827671A 1 PILOT CHECK ASSEMBLY
7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7F25201GD, 7F25203JB, 7F25203LB, 7F50412DD
825199
 
825199 PILOT
7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7055207GD, 7055207HB, 7055207TF, 7F25201GD, 7F25203JB, 7F25203LB, 7F30203H
37350
 
37350 PILOT WASHER
70432037D, 7055207GD, 7075217CD, 7100412CD
809578
809578 4
 
809578 4 PILOT SCREW SET
7F41452KD, 7F50352HD, 7F50412DD
809576
 
809576 PILOT JET (#44)
7F41452KD, 7F50352HD, 7F50412DD
809576 1
 
809576 1 PILOT JET (#42)
7F41452KD, 7F50352HD, 7F50412DD
Back to top