20009 Mariner PIN, DETENT-CONTROL HOUSING NEUTRAL WARM-UP LEVER


20009 PIN, DETENT-CONTROL HOUSING NEUTRAL WARM-UP LEVER Mariner 7070509, 7080508, 7090529, 7115528, 7115529, 7140528, 7140629 PIN
20009 PIN, DETENT-CONTROL HOUSING NEUTRAL WARM-UP LEVER Mariner
Rating:
43

Buy PIN, DETENT-CONTROL HOUSING NEUTRAL WARM-UP LEVER 20009 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

Compatible models:

Mariner entire parts catalog list:

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     207-5034 (1)     Stud Tensioner Tool Gp     1    
301-5215 (2) Stud Tensioner Tool Gp     1    
B     8T-3035     Hydraulic Line     1    
8T-0820 Hydraulic Pressure Gauge     1    
3S-6224 (3) Electric Hydraulic Pump
(115 Volt 50/50 Hz)     1    
8S-8033 (3) Electric Hydraulic Pump
(230 Volt 50/60 Hz)     1    
9U-6600 (3) Hand Hydraulic Pump     1    
C     8T-0960     Handling Tool Group     1    
D     134-0932     Main Bearing Driver     1    
E     8T-0516     Pry Bar     1    
( 1 ) Operating pressure is 65000 2400 kPa (9425 348 psi).
( 2 ) Operating pressure is 111500 3950 kPa (16170 575 psi).
( 3 ) Three hydraulic pumps are listed. Only one pump is necessary in order to carry out the job.Start By:
Remove the engine oil filler and the oil level gauge. Refer to Disassembly and Assembly, "Engine Oil Filler and Oil Level Gauge - Remove and Install".
Remove the crankcase explosion relief valves. Refer to Disassembly and Assembly, "Crankcase Explosion Relief Valve - Remove and Install".Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.Note: If the rear main bearing is being removed, remove the guards and disconnect the drive coupling.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00571829
The Illustration does not show the retainer as part of the collar assembly.
Illustration 2 g00577004
Illustration 3 g00577005
Note: Inspection or replacement of the main bearing can be done with the crankshaft in place. The stud tensioner tool group is used with the handling tool group. The stud tensioner tool group and the main bearing cap can be raised and lowered by using the handling tool group.The handling tool group includes supports (1), movable tray (3), and pins (2). Pins (2) are installed in the main bearing cap during removal.Brackets (4) of the handling tool group are bolted to the openings of the crankcase access covers. Adjustment screws are used in order to level the tensioner or the main bearing caps.Note: When you assemble the handling tool group, always use the spring clips. The clips will prevent components from dropping into the oil pan. Link (5) connects to either the tensioner or pin (2) .
Remove the remaining crankcase access covers.
Illustration 4 g00644075
Note: The Collar Retainer, the Stud Tensioner Cylinder, and the Threaded Collar are part of Tooling (A) .
Place Collar Retainer (8) on top of Stud Tensioner Cylinder (7) in order to determine the bolts that need to be removed from the Stud Tensioner Cylinder. Remove the four appropriate bolts from the Stud Tensioner Cylinder.
Insert the Threaded Collar in the center of Stud Tensioner Cylinder (7) .
Install Collar Retainer (8) in order to retain Threaded Collar (6) in Stud Tensioner Cylinder (7) .
Use bolts (9) in order to fasten Collar Retainer (8) to Stud Tensioner Cylinder (7) .
Illustration 5 g00644078
Remove main bearing saddle bolts (10) from each side of the engine.Note: Before you install Tooling (A), move the crankshaft to a position that is out of the way of the connecting rod journal.
Illustration 6 g00577004
Put supports (1) and tray (3)


Parts pin Mariner:

47175
 
47175 PIN, LOCKING LEVER AND COVER FASTENING
7050716, 7060312PC, 7060524, 7070509, 7070520, 7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7135826, 7140528, 7140629, 7150629
28416
 
28416 PIN, UPPER SHOCK MOUNTING
7045217, 7050200, 7050716, 7060312PC, 7060524, 7070509, 7070520, 7080508, 7085507, 7090529, 7115528, 7115529, 7140528, 7140629
28414
 
28414 PIN, LOWER SHOCK MOUNTING MERC 850 LONG
7080508, 7080629, 7085507, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
20033
 
20033 PIN, DOWEL - CRANKCASE TO CYLINDER BLOCK
7002201DK, 70404119D, 7045217, 7050200, 7050412YD, 7050716, 7050717, 7060312PC, 7060412ET, 7060524, 7070509, 7070520, 7075312ND, 7075312SD, 7075524, 7075717, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7100412NC, 7115412TB, 7115520, 7115528
27961
 
27961 PIN, ECONOMIZER COLLAR - SPRING RETAINER
7115528, 7115529, 7140528, 7140629
29908
 
29908 PIN, ROLL - FLANGE LOCATING
7115528, 7115529, 7140528, 7140629, 7B25201GF
26618
 
26618 PIN, DOWEL - PULLEY TO FLYWHEEL
7115528, 7115529, 7140528, 7140629, 7200620
Back to top