91793M Mariner PIN


91793M PIN Mariner 7004201, 7005201, 7005207, 7008204, 7008208, 7008226 PIN
91793M PIN Mariner
Rating:
28

Buy PIN 91793M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 36
 

Compatible models:

Mariner entire parts catalog list:

7004201 1981,1985,1988,1989
7005201 1981,1985,1988,1989
7005207 1977
7008204 1984,1985,1986
7008208 1978
7008226 1986

Information:

Introduction
Table 1
Revision     Summary of Changes in SEBF9330    © 2014 Caterpillar All Rights Reserved. This guideline is for the use of Cat dealers only. Unauthorized use of this document or the proprietary processes therein without permission may be violation of intellectual property law. Information contained in this document is considered Caterpillar: Confidential Yellow.This Reuse and Salvage Guideline contains the necessary information in order to allow a dealer to establish a parts reusability program. Reuse and salvage information enables Caterpillar dealers and customers to benefit from cost reductions. Every effort has been made in order to provide the most current information that is known to Caterpillar. Continuing improvement and advancement of product design might have caused changes to your product which are not included in this publication. This Reuse and Salvage Guideline must be used with the latest technical information that is available from Caterpillar.For questions or additional information concerning this guideline, submit a form for feedback in the Service Information System. In order to address an urgent issue, use the following resources in order to communicate your request to Caterpillar Repair Process Engineering:
Caterpillar Dealer Technical Communicator
Dealer Solution Network
Caterpillar Technical Representative
Knowledge NetworkCanceled Part Numbers and Replaced Part Numbers
This document may include canceled part numbers and replaced part numbers. Use NPR on SIS for information about canceled part numbers and replaced part numbers. NPR will provide the current part numbers for replaced parts.Important Safety Information
Illustration 1 g02139237
Follow all safety warnings. Most accidents that involve product operation, maintenance, or repair are caused by failure to observe safety warnings. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. Personnel must be properly trained in order to perform maintenance, repair, or operate any machine. Safety precautions and warnings are provided this instruction and on Caterpillar products. These warnings should be observed before performing any procedures. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in this publication and on the product are not all inclusive.The hazards are identified by the "Safety Alert Symbol" which is followed by a "Signal Word" such as "DANGER", "" or "CAUTION". The "" Safety Alert Symbol is shown in Illustration below.
Illustration 2 g00008666
Summary
This guideline provides the weld procedure to repair cracks and cracked welds around the loader frame at the "A" pins and contains upgrades for reinforcing the front loader frame at the "A" pins. The addition of the doubler plates to the loader frame plate at the inboard end of the "A" pin will improve frame durability and life.
Illustration 3 g03541578
Front loader frame "A" pin potential crack failure (A) 113-5119 Plate Required Parts
Table 2
Quantity     Part Number     Description    
2     350-0708     Plate    
2     350-0709     Plate    
2     291-2832     Plate    Replacement / Fabricated Parts
When replacement parts are required for this product Caterpillar recommends using Caterpillar replacement parts or parts with equivalent specifications including, but not limited too physical dimensions, type, strength, and material. Failure to heed this warning can lead to premature failures, product damage, personal injury, or death.
Illustration 4 g03543470
(1) 350-0708 Plate
Illustration 5 g03543475
(2) 350-0709 Plate
Illustration 6 g03543485
(3) 291-2832 Plate (4) Bore out the hole to 207 2 mm (8.1495 0.0787 inch)References
Use the following references for additional information regarding work outlined in this document.


Parts pin Mariner:

80451M
 
80451M PIN, FLOAT
7004201, 7005201, 7005207, 7008218EW, 7008238, 7008247, 7008305, 7008425, 7010209, 7015529, 7F08203HF, 7F08261DF
81888M
 
81888M PIN
7003207, 7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320
14193M
 
14193M PIN, CRANKSHAFT 1
7005201, 7005207, 7008218EW, 7008425
95601M
 
95601M PIN
7004201, 7005201, 7005207, 7008204, 7008208, 7008218EW, 7008226, 7008305, 7008425
82161M
 
82161M PIN, DOWEL-CRANKCASE...
7008208, 7008238, 7008247, 7008248, 7008305, 7015207, 7015307, 7015327
82359M
 
82359M PIN, DOWEL DRIVESHAFT HOUSING...
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
82354M
 
82354M PIN, DOWEL...
7004201, 7008204, 7008208, 7008218EW, 7008226, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015307, 7015327, 7015529, 7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7
82148M
 
82148M PIN, ROLL-CAM...
7008204, 7008208, 7008226, 7008238, 7008247, 7008248, 7015207, 7015307, 7015327, 7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320
Back to top