44484T Mariner PINION GEAR, (13 Teeth)


44484T PINION GEAR, (13 Teeth) Mariner 7055207HB, 7075217HD, 7100412HB, 7A41412LB, 7F30203HD, 7F30203LB, 7F40452KD, 7F40452LB, 7F41452KB, 7F41452KD PINION

Buy PINION GEAR, (13 Teeth) 44484T Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$212.02

10-02-2025
1.0[0.45] Pounds
US: Devils Lake Marine a
MERCURY Gear-Pinion mfg Part Number 44484T
MERCURY
Number on catalog scheme: 15
 

Information:

Engine Speed Governing
The master ECM maintains the desired engine speed by controlling the actuator for the throttle. The actuator is located at the inlet to the aftercooler. The actuator is electrically controlled and electrically actuated.The master ECM issues a throttle command that represents a percent of the level of electrical current. The output can be viewed on Caterpillar Electronic Technician (ET).Desired engine speed is determined by the following:
Status of the idle/rated switch
Desired speed input (analog voltage or 4 to 20 mA)
Programmable ParametersAir/Fuel Ratio Control
The master ECM provides control of the air/fuel mixture for performance and for efficiency at low emission levels. The system consists of an electronic fuel metering valve, output drivers in the master ECM, and maps in the master ECM. The control compensates for changes in the BTU of the fuel in order to maintain desired emission levels.The following steps describe the basic operation:
The master ECM determines the desired flow rates for the air and for the fuel. The flow rates are determined by these factors:
Desired engine speed
Actual engine speed
Calculated engine load
The command for the flow of the fuel is sent to the electronic fuel metering valve via the CAN data link.This process is repeated continuously during engine operation.Start/Stop Sequencing
The master ECM contains the logic and the outputs for control of starting and of shutdown. The customer programmable logic responds to signals from the following components: engine control, emergency stop switch, remote start switch, data link and other inputs.When the programmable logic determines necessary to crank the engine, the master ECM supplies +Battery voltage to the relay for the starting motor. The master ECM removes the voltage when the programmable crank terminate speed is reached or when a programmable cycle crank time has expired.The engine must be equipped with an energize-to-run type of gas shutoff valve (GSOV). The source of the voltage to the GSOV depends on the engine configuration. The GSOV may be energized by customer equipment or by the engine control system.If the engine control system controls the GSOV, the master ECM supplies +Battery voltage to the GSOV whenever the programmable logic determines that fuel is required to operate the engine.For more information on programmable parameters, refer to Troubleshooting, "Programming Parameters".Engine Monitoring and Protection
The control system monitors both the engine operation and the electrical circuits for the engine.Problems with engine operation such as low oil pressure produce an event code. The master ECM can issue a warning or a shutdown. This depends on the severity of the condition. For more information, refer to Troubleshooting, "Event Codes".Problems with an electrical circuit such as an open circuit produce a diagnostic code. For more information, refer to Troubleshooting, "Diagnostic Trouble Codes".Ignition Control
The control system provides variable ignition timing that is sensitive to detonation.Each cylinder has an ignition transformer that is located under the valve cover for the cylinder. To initiate combustion, an ECM sends a pulse of approximately 100 V to the primary coil of an ignition transformer at the appropriate time and for the appropriate duration. The transformer steps up the voltage in order to create a spark across the spark plug electrode.Detonation sensors monitor the engine for excessive detonation. The engine has ten detonation sensors. Each sensor monitors two adjacent cylinders. The sensors generate data on vibration that is processed by each ECM in order to determine detonation levels. If detonation reaches an unacceptable level, the appropriate ECM retards the ignition timing of the affected cylinder or cylinders. If retarding the timing does not limit detonation to an acceptable level, the master ECM shuts down the engine.The master ECM and the slave ECM provide extensive diagnostics for the ignition system. The master ECM can receive a discrete input for ignition timing in order to allow operation with alternate fuels such as propane that requires a timing offset.


Parts pinion Mariner:

44484
 
44484 PINION GEAR
7050302ED, 7050412YD, 7055207GD, 7060412ET, 7075217CD, 7075312ND, 7075312SD, 7075717, 7100412CD, 7F41452KD, 7F50352HD, 7F50412DD
12349A 2
 
12349A 2 PINION GEAR LOCATING TOOL
70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7055207GD, 7055207HB, 7055207TF, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412T
822161 2
 
822161 2 PINION GEAR (12 TEETH)
70432037D, 7F41452KD, 7F50352HD
817008A 2
 
817008A 2 PINION GEAR LOCATING TOOL
70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7055207GD, 7055207HB, 7055207TF, 7A30302LB, 7A30453VZ, 7A40302UD, 7A40302ZZ, 7A40312UZ, 7A40312ZZ, 7A40412ZZ, 7A41412LB, 7A41452I
821326T 1
 
821326T 1 PINION GEAR, (13 Teeth)
7031203GD, 7031207LF, 7031312TB, 7041203GB, 7A30302LB, 7A40302UD, 7A40312UZ, 7F30203HD, 7F30203LB, 7F40203UD, 7F40213UZ, 7F40452KD, 7F40452LB
68575T 2
 
68575T 2 PINION
7A30302LB, 7A40302UD, 7A41412LB, 7F10203HD, 7F13203UB, 7F25203JB, 7F25203LB, 7F30203HD, 7F30203LB, 7F40452KD, 7F40452LB, 7F41452KB, 7F41452KD
13310T 1
 
13310T 1 PINION ASSEMBLY
7100412HB, 7115412TB, 7135412JD, 7150413LD, 7150423JD, 7200413JD, 7225412HD, 7225413HD
891754T
 
891754T PINION
7A30302LB, 7A41412LB, 7F25203LB, 7F30203LB, 7F40452LB
Back to top