81096M Mariner PISTON RING SET (1ST O.S. 67.25 MM)


81096M PISTON RING SET (1ST O.S. 67.25 MM) Mariner 7020201, 7025200, 7025207NW, 7025207PW, 7025500, 7026226, 7028207, 7028527 PISTON

Buy PISTON RING SET (1ST O.S. 67.25 MM) 81096M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Mariner entire parts catalog list:

7020201 1981
7025200 1980
7025207NW 1988
7025207PW 1989,1990,1991,1992,1993
7025500 1980
7026226 1986,1988
7028207 1977
7028527 1977

Information:


Table 1
Alternative     Default    
"J1/P1:10"
"J1/P1:12"
"J1/P1:13"     "None"    "Engine Shutdown Output"
Output 2, output 3 or output 4 is available for the connection of an engine shutdown output relay that is used to shut down the vehicle electrical system after the idle timer has expired. The "Engine Shutdown Output" can be programmed to J1/P1:10, to J1/P1:12 or to J1/P1:13. The "Engine Shutdown Output" comes on after the engine runs for more than three seconds. The "Engine Shutdown Output" turns off when the engine rpm is at least 100 rpm below the low idle rpm for more than three seconds.
Table 2
Alternative     Default    
"J1/P1:10"
"J1/P1:12"
"J1/P1:13"     "None"    "Auxiliary Brake"
The auxiliary brake output is for use with a BrakeSaver or other aftermarket braking devices. Output 3 is available for the connection of an auxiliary brake relay. This parameter ("Auxiliary Brake") must be programmed to J1/P1:12. Operation of the auxiliary brake and the relay is inhibited during undesirable engine operating conditions. The time period of fueling the engine is an undesirable engine operating condition.
Table 3
Alternative     Default    
"J1/P1:12"     "None"    "Starting Aid Output"
Output 2, output 3 or output 4 is available for the connection of the starting aid relay or the starting aid solenoid. If a starting aid switch is not used, the starting aid output will turn on automatically when operating conditions require the use of a starting aid. If the "Starting Aid On/Off Switch" parameter is programmed and a switch connected to the corresponding switch input, the starting aid output will not function when the switch is in the OFF position.
Table 4
Alternatives    Default    
"J1/P1:10"
"J1/P1:12"
"J1/P1:13"     "None"    "Air Inlet Shutoff Relay Control"
The air inlet shutoff is available for certain engine ratings that operate in areas with large amounts of combustible gases. The air inlet shutoff will protect the engine from an engine overspeed when these gases are present. If this option is installed, the "Air Inlet Shutoff Relay Control" cannot be turned off. J1/P1:62 must be connected to the +Battery in order for the air inlet shutoff to operate. If a neutral switch is installed in the vehicle, the neutral switch must be connected to J1/P1:62. The air inlet shutoff will only operate when the transmission is in neutral.
Table 5
Alternatives    Default    
"J2/P2:13"     "None"    "Fan Control Type"
If the ECM is used to operate the cooling fan, this parameter must be programmed to "On/Off", to "Three-Speed Fan", or to "Variable Speed Fan Option S". This parameter must be programmed to "None" if the ECM is not operating the cooling fan relay or the cooling fan solenoid.
Table 6
Alternative     Default    
"On/Off"
"Three-Speed Fan"
"Variable Speed Fan Option S"     "None"    "PTO Active Output"
The "PTO Active Output" parameter allows the use of an output when the engine is in PTO mode. The PTO switch must be on in order for the "PTO Active Output" to function. The "PTO Active Output" will stay active until there is a kickout of PTO mode or the PTO switch is turned to the OFF position.
Table 7
Alternative     Default    
"J1/P1:19"     "None"    


Parts piston Mariner:

6937M
 
6937M PISTON (STD 66.96 MM)
7028207, 7028527
6785M
 
6785M PISTON (STD 66.97 MM)
7028207, 7028527
6786M
 
6786M PISTON (STD 66.98 MM)
7028207, 7028527
6787M
6788M
8377M
 
8377M PISTON ASS'Y (2ND O.S. 67.50MM)
7020201, 7025200, 7025207PW, 7025500, 7026226
8428M
 
8428M PISTON ASS'Y (STD)
7025207NW, 7025207PW
8429M
Back to top