15966 Mariner PLATE


15966 PLATE Mariner 7135D73ZY, 7150413UY, 7150413ZY, 7200413UY, 7200413ZY, 7200423UY, 7200D73IY, 7200D73MD, 7200D73RD, 7200D73ZY, 7225413IY, 7225413ZY, 7225E73MD, 7250423IY PLATE
15966 PLATE Mariner
Rating:
8

Buy PLATE 15966 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Mariner entire parts catalog list:

7135D73ZY 2006
7150413UY 2006
7150413ZY 2006
7200413UY 2006
7200413ZY 2006
7200423UY 2006
7200D73IY 2006
7200D73MD 2003
7200D73RD 2004,2005,2006
7200D73ZY 2006
7225413IY 2006
7225413ZY 2006
7225E73MD 2003,2004
7250423IY 2006

Information:

Drain the Cooling System
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Cat Dealer Service Tool Catalog" or refer to Special Publication, PECJ0003, "Cat Shop Supplies and Tools Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Stop the engine and allow the engine to cool. Ensure that the engine will not start when the cooling system is drained.
Loosen the cooling system filler cap slowly to relieve any pressure. Remove the cooling system filler cap.
Illustration 1 g06165924
(1) Coolant drains
(2) Coolant drains
Illustration 2 g06165927
(3) Drain plug
(4) Drain plug
Illustration 3 g06423959
(5) Drain for heat exchanger
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove one of the drain plugs.Note: If equipped, be sure to drain the heater and any related supply and return lines.Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Cat dealer or consult Cat Dealer Service Tool Group:Inside USA 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
International 1-309-578-7372
Flush
Systems Filled with Cat ELC, Cat ELI, or a Conventional Coolant that Meets the Cat EC-1 Requirements and the Standards of ASTM D6210
Flush the cooling system with clean water to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual, SENR3130, "Torque Specifications" for more information on the proper torques.
Fill the cooling system no faster than 5 L (1.32 US gal) per minute to avoid air locks.
Fill the cooling system with clean water. Install the cooling system filler cap.
Start and run the engine at low idle until the temperature reaches 49 to 66 °C (120 to 150 °F).
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual, SENR3130, "Torque Specifications" for more information on the proper torques.
Fill the cooling system no faster than 5 L (1.32 US gal) per minute to avoid air locks.
Fill the cooling system with a mixture of clean water and Cat Fast Acting Cooling System Cleaner.
Choose 1 of the following options.
Add 0.5 L (1 pt) of cleaner per 15 L (4 US gal) of the cooling system capacity.
For cooling systems with heavy deposits or plugging, add 0.5 L (1 pt) of cleaner per 3.8 to 7.6 L (1 to 2 US gal) of the cooling system capacity.
Install the cooling system filler cap.
Start and run the engine at low idle for a minimum of 30 minutes. For cooling systems with heavy deposits or plugging, run the engine for 90 minutes. The coolant temperature should be at least 76° C (168° F).
Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. If equipped, be sure to flush the heater and any related supply and return lines. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual, SENR3130, "Torque Specifications" for more information on the proper torques.Fill the Cooling System


Parts plate Mariner:

18233A20
PLATE ASSEMBLY, Driveshaft Housing
18233A20 PLATE ASSEMBLY, Driveshaft Housing
7135412JD, 7135473KD, 7135D73RD, 7135D73UY, 7135D73ZY, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7200413UY, 7200413ZY, 7200423UY
880791
881004
832935A17
PLATE ASSEMBLY, Exhaust
832935A17 PLATE ASSEMBLY, Exhaust
7200D73IY, 7200D73RD, 7200D73ZY, 7225413IY, 7225413RD, 7225413ZY, 7225E73MD, 7250423IY
888910
PLATE
888910 PLATE
7200D73IY, 7200D73RD, 7200D73ZY, 7225413IY, 7225413RD, 7225413ZY, 7225E73MD, 7250423IY
899071T01
PLATE
899071T01 PLATE
7135D73ZY, 7200D73IY
828343A05
PLATE ASSEMBLY, Exhaust Divider
828343A05 PLATE ASSEMBLY, Exhaust Divider
7135D73ZY, 7150413UY, 7150413ZY, 7200413UY, 7200413ZY, 7200423UY
Back to top