18260T 2 Mariner PLATE ASSEMBLY, Exhaust


18260T 2 PLATE ASSEMBLY, Exhaust Mariner 7135412JD, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7150423JD, 7200413JD, 7200413UY, 7200413ZY, 7200423UY PLATE
18260T 2 PLATE ASSEMBLY, Exhaust Mariner
Rating:
68

Buy PLATE ASSEMBLY, Exhaust 18260T 2 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 26
 

Mariner entire parts catalog list:

7135412JD 2000,2001,2002,2003,2004,2005
7150413LD 2002,2003
7150413RD 2004,2005
7150413UY 2006
7150413ZY 2006
7150423JD 2000,2001
7200413JD 2000
7200413UY 2006
7200413ZY 2006
7200423UY 2006

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B 6V-3143
or
1U-7325 Distorter Adapter 1
C 5P-7409 Sleeve Distorter 1
D 6V-4003 (1) Seal Locator As 1
2N-5006 (1) Bolt 2
E 8T-3099 (1) Seal Installer 1
F 9S-8858 (1) Nut 1
G - Loctite 7649 Primer N 1
H - Loctite 620 Retaining Compound 1
J 452-6011 Multipurpose Grease 1
K 484-7863 (2) Tool As 1
(1) For installation of seals 113-8432, 113-8433, 175-5290, 197-3889, 569-7728, and 569-7729
(2) For Installation of seals 436-1478 and 436-1479Start By:
Remove the flywheel.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Every time that the crankshaft seal is removed from the wear sleeve, a new wear sleeve and crankshaft seal must be installed.
For 3520 engine crankshafts not using the oil fed damper remove the oil plug on the front face of the crankshaft.
Illustration 1 g00659239
Drill three evenly spaced holes in crankshaft rear seal (1). Use Tooling (A) to remove crankshaft rear seal (1).
Illustration 2 g00659240
Insert Tooling (B) between the rear housing and wear sleeve (2).
The use of excessive force on the sleeve distorter can cause the distorter adapter to crack the housing. To help avoid damage to the engine, do not use excessive force to remove the wear sleeve.
Insert Tooling (C) between Tooling (B) and wear sleeve (2). Carefully turn Tooling (C) until the edge of the tool causes a crease in wear sleeve (2).Repeat this procedure several times around wear sleeve (2) until wear sleeve (2) can be removed by hand.Installation Procedure For Seals 113-8432, 113-8433, 175-5290, 197-3889, 569-7728, and 569-7729
Note: The crankshaft rear seal and the wear sleeve must be replaced at the same time. Once the crankshaft rear seal and the wear sleeve are separated, these components cannot be used again.Note: Do not use any type of lubricant during the installation of the crankshaft rear seal and the wear sleeve.
For 3520 engine crankshafts not using the oil fed damper remove the oil plug on the front face of the crankshaft.
Before installation of the crankshaft rear seal and the wear sleeve, inspect the crankshaft for scratches. Also, inspect the crankshaft for any distortion on the surface that may lead to an out of round condition. Use a polishing cloth to remove any imperfections on the crankshaft.
Inspect the seal and mating hardware for any obvious issues or contamination. Clean any oil that is on the housing.
Illustration 3 g06565320
Small lathe groove only used on 569-7728 Crankshaft Seal and 113-8432 Seal.
Check for the correct sleeve and chamfer direction.
Clean the outer diameter of the crankshaft and the inner diameter of the new wear sleeve with Tooling (G).
Apply Tooling (H) to the outer diameter of the crankshaft and the inner diameter of the new wear sleeve.
If the crankshaft seal and the wear sleeve come apart during installation, the crankshaft seal and the wear sleeve must be replaced.
Note: The front crankshaft seal and the wear sleeve cannot be interchanged with the rear crankshaft seal and the wear sleeve.


Parts plate Mariner:

65664A 1
 
65664A 1 PLATE ASSEMBLY
7135826, 7150629, 7175629, 7200413JD, 7200473FD, 7200473GD, 7200473HD, 7200473JD, 7200473KD, 7200620, 7200D73IY, 7200D73MD, 7200D73RD, 7200D73ZY, 7220727, 7225412CD, 7225412HD, 7225413DD, 7225413HD, 7225413IY, 7225413LD, 7225413RD, 7225413ZY, 7225E73
813501
PLATE
813501 PLATE
7150413ED, 7150413HD, 7150423JD, 7175413AD, 7175413PD, 7175413YD, 7175423HD, 7200413JD
18233A 8
 
18233A 8 PLATE ASSEMBLY, Driveshaft Housing
7115473JD, 7135412JD, 7135473KD, 7150413LD, 7150423JD, 7200413JD
828343T 3
 
828343T 3 PLATE, Exhaust Divider
7115473JD, 7135412JD, 7150423JD, 7200413JD
857162 1
 
857162 1 PLATE, CDM Mounting
7135412JD, 7150423JD, 7200413JD
18233A20
PLATE ASSEMBLY, Driveshaft Housing
18233A20 PLATE ASSEMBLY, Driveshaft Housing
7135412JD, 7135473KD, 7135D73RD, 7135D73UY, 7135D73ZY, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7200413UY, 7200413ZY, 7200423UY
840422A 1
 
840422A 1 PLATE KIT
7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7200413UY, 7200413ZY, 7200423UY
880188F 1
 
880188F 1 PLATE, Coil
7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7200413UY, 7200413ZY, 7200423UY
Back to top