54705 Mariner PLATE, FACE - WATER PUMP BASE TO WATER PUMP BODY


54705 PLATE, FACE - WATER PUMP BASE TO WATER PUMP BODY Mariner 70404119D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520 PLATE
54705 PLATE, FACE - WATER PUMP BASE TO WATER PUMP BODY Mariner
Rating:
18

Buy PLATE, FACE - WATER PUMP BASE TO WATER PUMP BODY 54705 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Mariner entire parts catalog list:

70404119D 1989,1990,1991,1992,1993,1994,1995,1996,1997
7045217 1987,1988,1989
7050200 1980,1982,1983,1985,1986
7050716 1986
7050717 1987,1988,1989,1990
7060312PC 1989
7060524 1984,1985,1986,1989,1990
7070509 1979
7070520 1980,1982,1983

Information:

SUBJECT: ENGINE OIL LEVEL GAUGE MAY BE INCORRECTLY MARKED ON CERTAIN 966G II AND 972G II WHEEL LOADERS
PROBLEM:
The engine oil level gauge may be incorrectly marked on certain 966G II and 972G II Wheel Loaders. This may result in under-filling the engine crankcase by approximately 3 liters relative to the correct refill level of 35 liters.
SOLUTION:
A new oil level gauge will be available soon to replace the 228-5226 and 233-6201 Oil Level Gauge Group (Dipstick). Until the replacement gauge is available, the following procedure may be applied.
Check the calibration of the oil level dipstick at oil and filter change period using the following procedure:
Insure that the machine is on a level surface. Operate the engine until normal operating temperature is achieved. Stop the engine. Remove the crankcase oil drain plugs. The oil drain plug from the deep portion of the oil pan should be removed. The oil drain plug from the shallow portion of the oil pan should be removed. This will allow all of the oil to drain. Drain the oil from the crankcase for 20 minutes.
Remove the used oil filter(s). Install the new oil filter(s). Install the oil drain plugs and tighten to 70 ? 15 N?m (50 ? 11 lb ft).
Note: Your engine may be equipped with auxiliary oil filters. The auxiliary oil filters require a different volume of oil. Refer to the OEM specifications for the auxiliary oil filter.
Pour 27 L (28.5 qt) of oil into the crankcase. Allow enough time for the oil to drain into the crankcase. Approximately 20 minutes should be allowed. Check the oil level. Wait for several minutes and check the oil level again. Proceed after the oil level stops changing.
Check the oil level on the oil level gauge. The oil level should be at the "ADD" mark. If the oil level is not at the existing "ADD" mark, grind off the "ADD" mark and engrave the new "ADD" level. Use an engraving pen in order to engrave the new "ADD" mark.
Pour 4 L (4 qt) of oil into the crankcase. Allow enough time for the oil to drain into the crankcase.
Check the oil level on the oil level gauge. The oil level should be at the "FULL" mark. If the oil level is not at the existing "FULL" mark, grind off the "FULL" mark. Use an engraving pen in order to engrave the new "FULL" mark.
Do not crank the engine for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking again.
Pour an additional 4 L (4 qt) of oil into the crankcase. Start the engine and run the engine enough to ensure that the lubrication system is filled. Inspect the engine for oil leaks.
Stop the engine and allow enough time for the oil to drain into the crankcase.
Check the oil level on the oil level gauge. If the oil level is not at the calibrated "FULL" mark, fill the crankcase to the calibrated "FULL" mark. Record the amount of oil that was added. The additional oil and the 31 L (33 qt) of oil that was in the crankcase is the oil capacity of the lubrication system. Record the oil capacity of the lubrication system for future oil changes.
COPYRIGHT 2004 CATERPILLAR
ALL RIGHTS RESERVED


Parts plate Mariner:

76251A 1
 
76251A 1 PLATE ASSEMBLY, FRONT COVER MOUNTING
7050716, 7060312PC, 7060524, 7070509, 7070520
69579
 
69579 PLATE, BAFFLE-EXHAUST MANIFOLD
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
73627
73439
 
73439 PLATE, MOUNTING-IGNITION COIL
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
37691
 
37691 PLATE, CABLE GUIDE
7045217, 7050200, 7050716
61002
 
61002 PLATE, STARTER REWIND
70404119D, 7045217, 7050200, 7050716
48519
 
48519 PLATE, COVER - DRIVE WHEEL
70404119D, 7045217, 7050200, 7050302ED, 7050412YD, 7050716, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075312ND, 7075312SD, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 707
Back to top