82857M STOPPER PLATE Mariner
7003207, 7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008218EW, 7008226, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028207,
STOPPER
Price: query
Rating:
Compatible models:
Mariner entire parts catalog list:
- REVERSE LOCK » 82857M
7005201 1981,1985,1988,1989
7005207 1977
- REVERSE LOCK » 82857M
- DRIVESHAFT HOUSING- CLAMP AND SWIVEL BRACKET » 82857M
- REVERSE LOCK » 82857M
- REVERSE LOCK » 82857M
- REVERSE LOCK » 82857M
- REVERSE LOCK » 82857M
- REVERSE LOCK » 82857M
- REVERSE LOCK » 82857M
- REVERSE LOCK » 82857M
- REVERSE LOCK » 82857M
- REVERSE LOCK » 82857M
- REVERSE LOCK » 82857M
- REVERSE LOCK » 82857M
- REVERSE LOCK » 82857M
- CLAMP AND SWIVEL BRACKET » 82857M
- REVERSE LOCK » 82857M
- REVERSE TILT LOCK » 82857M
- REVERSE TILT LOCK » 82857M
- CLAMP AND SWIVEL BRACKET » 82857M
7025200 1980
- CLAMP AND SWIVEL BRACKET-REVERSE LOCK » 82857M
- CLAMP AND SWIVEL BRACKET-REVERSE LOCK » 82857M
7025207PW 1989,1990,1991,1992,1993
- CLAMP AND SWIVEL BRACKET » 82857M
- SWIVEL-CLAMP BRACKET » 82857M
- CLAMP AND SWIVEL BRACKET-REVERSE LOCK » 82857M
- CLAMP AND SWIVEL BRACKET-REVERSE LOCK » 82857M
7028207 1977
- REVERSE LOCK » 82857M
- REVERSE LOCK » 82857M
- CLAMP AND SWIVEL BRACKET-REVERSE LOCK » 82857M
- CLAMP AND SWIVEL BRACKET-REVERSE LOCK » 82857M
- CLAMP AND SWIVEL BRACKET-REVERSE LOCK » 82857M
- CLAMP AND SWIVEL BRACKET-REVERSE LOCK » 82857M
7030301 1981
7030320 1980,1990,1992
Information:
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1U-7307     Governor Repair Fixture (1)     1    
B     1P-1855     Retaining Ring Pliers     1    
C     1P-1857     Retaining Ring Pliers     1    
D     1U-7606     Servo Block (1)     1    
E     1U-7277     Pin Punch     1    
F     1U-7635     Clevis Driver (1)     1    
( 1 ) Part of former 1U-9088 Governor Tool Group
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Inspect all parts of the governor upon disassembly. For information on the reusability of components in the governor, refer to the Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines Equipped with Mechanical Unit Injectors (MUI)". For information on cleaning the components in the governor, refer to the Cleaning Guide, SEBF8354, "Equipment And Chemical Recommendations Reference Manual".Note: Refer to Chart A "Parts to be Replaced During Rebuild" in Guideline For Reusable Parts And Salvage Operations, SEBF8434 for a list of components that need to be replaced during a governor rebuild. It is not necessary to replace the components in Chart A "Parts to be Replaced During Rebuild" if the governor is in the shop for a bench test or for minor repair.Note: Early Type II Governors had limited production until 1991. The early Type II Governors may be inspected and perhaps reconditioned. However, some of the internal components are no longer serviced or the internal components may only be serviced by larger assemblies. When you recondition a Type II Governor, it may be necessary to replace the governor. If extensive repair work is necessary, a Type II Governor can be replaced with a Type IV Governor.
Illustration 1 g00521797
Typical Governor (1) Bolt (2) Orifice for the dashpot (3) O-ring seal (4) Bolt (5) Cover (6) Cover assembly (7) O-ring seal (8) Shims (9) Rear spring seat (10) Retaining ring (11) Spacer (12) Piston assembly for the dashpot (13) Shims for the high idle governor (if equipped) (14) Spring pair (15) Spring seat assembly
Mount the drive gear end of the governor on the 1U-7307 Governor Repair Fixture (Tool (A) ).
Illustration 2 g00521798
Remove three bolts (4) .
Remove cover (5) .
Illustration 3 g00521800
Remove O-ring seal (3) from cover (5). Inspect the O-ring seal for wear or damage. If the O-ring seal is worn or damaged, use a new part for replacement.
Illustration 4 g00521801
Ensure that orifice (2) for the dashpot is not plugged. Also ensure that orifice (2) is tight in the casting.Note: The orifice for the dashpot may be drilled directly into the governor rear housing or the orifice may be a fitting that is staked into the governor rear housing. Ensure that all orifice fittings are staked into the governor housing before reassembly.
Parts stopper Mariner:
80640M
81531M
81531M STOPPER
7020201, 7025200, 7025207NW, 7025500, 7028207, 7028527, 7030200, 7040202, 7040207, 7040208, 7040328, 7040507, 7040716, 7048207, 7048227, 7060507, 7060528
81149M
97756M
97756M STOPPER
7008204, 7008208, 7008218EW, 7008226, 7008425, 7010209, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207PW, 7040208PW, 7040706, 7040716, 7048227, 7048
11445M
83266M
80185M
81125M