92815 Mariner PLATE, SUPPORT - EXHAUST TUBE


92815 PLATE, SUPPORT - EXHAUST TUBE Mariner 70404119D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070520 PLATE
92815 PLATE, SUPPORT - EXHAUST TUBE Mariner
Rating:
48

Buy PLATE, SUPPORT - EXHAUST TUBE 92815 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

Mariner entire parts catalog list:

70404119D 1989,1990,1991,1992,1993,1994,1995,1996,1997
7045217 1987,1988,1989
7050200 1980,1982,1983,1985,1986
7050716 1986
7050717 1987,1988,1989,1990
7060312PC 1989
7060524 1984,1985,1986,1989,1990
7070520 1980,1982,1983

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 136-4632 Timing Pin (Crankshaft) 1
C 1P-2320 Combination Puller 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all hoses, on all hose assemblies and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. Plugging all hose assemblies and tube assemblies helps to prevent fluid loss and also helps to keep contaminants from entering the system.
Do not disconnect the air lines until the air pressure in the system is at zero. If hose is disconnected under pressure it can cause personal injury.
Release the pressure from the air system. Refer to the Original Equipment Manufacture (OEM) for the correct procedure.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
If the engine is equipped with a hydraulic pump on the rear of the air compressor, remove the hydraulic pump. Refer to the OEM for the correct procedure.
Use Tooling (A) to rotate the crankshaft so that number one piston is at the top center position on the compression stroke. Refer to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.Note: The air compressor must be timed with the engine to minimize engine vibration.
Illustration 1 g01966313
Typical example
Remove plug (2) from the cylinder block. Remove O-ring seal (1) from the plug.
Install Tooling (B) into Hole (X) in the cylinder block. Use Tooling (B) to lock the crankshaft in the correct position.Note: Do not use excessive force to install Tooling (B). Do not use Tooling (B) to hold the crankshaft during repairs.
Illustration 2 g01964836
Typical example
Illustration 3 g01965121
Typical example
Slide hose clamps along coolant hose (3) and coolant hose (4). Disconnect coolant hose (3) and coolant hose (4) from air compressor (6).
Disconnect the air lines from port (5) (not shown) and air lines from port (7). Refer to the OEM for the correct procedure.
Remove banjo bolt (9) and sealing washers from air compressor (6).
Remove bolt (10) and bolt (12) from support bracket (11) and remove the support bracket.
Support air compressor (6) and remove nuts (15). Remove the air compressor from front housing (8).
If necessary, remove studs (14) from front housing (8).
If necessary, remove bolts (17) and remove plate (16). Remove O-ring seal (13) from plate (16).
Illustration 4 g01964860
Typical example
Remove O-ring seal (21) from air compressor (6).
If necessary, follow Step 15a through Step 15b to remove gear (18) from the crankshaft of the air compressor.
Use a suitable tool to prevent the shaft of the compressor from rotating. Remove nut (20) and remove spring washer (19).
Use Tooling (C) to remove gear (18) from the crankshaft of the air compressor.
Illustration 5 g02091596
If nece


Parts plate Mariner:

73439
 
73439 PLATE, MOUNTING-IGNITION COIL
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
54705
 
54705 PLATE, FACE - WATER PUMP BASE TO WATER PUMP BODY
70404119D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
60570
 
60570 PLATE, RETAINER-ACTUATOR HOUSING
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
8852
 
8852 PLATE ASSEMBLY, DRIVE END
7050716, 7060312PC, 7060524, 7070520, 7075524, 7080629
90421
 
90421 PLATE, BAFFLE-EXHAUST MANIFOLD
7045217, 7050200, 7050716
42819A 2
88322
 
88322 PLATE, SWITCH BOX
7045217, 7050200, 7050716
88935
 
88935 PLATE, SWITCH BOX
7050716, 7060312PC, 7060524, 7070520
Back to top