97734M Mariner PLATE


97734M PLATE Mariner 7040202, 7040206, 7040706, 7040716 PLATE
97734M PLATE Mariner
Rating:
53

Buy PLATE 97734M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 24
 

Compatible models:

Mariner entire parts catalog list:

7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040706 1986,1990,1992
7040716 1986

Information:

Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps    Values    Results    
1. Incorrect Maintenance Intervals and/or Incorrect Oil
A. Use engine oil that is recommended and change the engine oil at the interval that is recommended by the engines Operation and Maintenance Manual.
   
Maintenance Intervals
   
Result: The engine oil was changed at the interval that is recommended by the engines Operation and Maintenance Manual.
Proceed to Test Step 2.
Result: The engine oil was not changed at the interval that is recommended by the engines Operation and Maintenance Manual.
Use at least the minimum grade of Cat oil.
Repair: Change the engine oil at the interval that is recommended. Repair or replace any damaged parts.
   
2. Contaminated Engine Oil
A. Obtain an S-O-S oil analysis. The analysis will contribute to a better understanding of oil contamination.
B. Check the oil filter bypass valve.
If the oil filter bypass valve is open, the oil will not be filtered. Check the oil filter bypass valve for a weak spring or for a broken spring. If the spring is broken, replace the spring. Verify that the oil bypass valve is operating correctly. Refer to the Disassembly and Assembly manual.
Refer to the Caterpillar guidelines for "Reusability and Salvage/Repair" for determining if the replacement of parts is necessary in order to perform a quality repair.
   
Contamination
   
Result: The oil is contaminated.
Repair: Determine the reason for any contamination of the engine oil and make the necessary repairs. Drain the crankcase and refill the crankcase with clean engine oil. Install new engine oil filters. Refer to the engines Operation and Maintenance Manual.
Result: The oil is not contaminated.
Proceed to Test Step 3.
   
3. Low Oil Pressure
A. Engine oil that is contaminated with another liquid can cause low engine oil pressure. High engine oil level can be an indication of contamination. Obtain an analysis of the engine oil.
B. The inlet screen of the suction tube for the engine oil pump can have a restriction. This restriction will cause cavitation and a loss of engine oil pressure. Check the inlet screen on the suction tube and remove any material that may be restricting engine oil flow.
When some components of the engine show wear in a short time, the cause can be a restriction in a passage for engine oil. An indicator for the engine oil pressure may indicate sufficient pressure, but a component is worn due to a lack of lubrication. In such a case, look at the passage for the engine oil supply to the component. Refer to Systems Operation/Testing and Adjusting, "Lubrication System" for additional information.
   
Restriction
   
Result: The inlet tube has a restriction.
Repair: Clear the obstruction. Verify the repair.
Result: The inlet tube does not have a restriction.
Proceed to Test Step 4.
   
4. Leaks in Air System
A. A leak in the air intake system may allow unfiltered air into the engine. Inspect the air intake system for streaks which may indicate a leakage of unfiltered air. Inspect all of the gaskets and the connections.
   
Air Leak
   
Result: There are no air leaks.
Proceed to Test Step 5.
Result: There are air leaks.
Repair: Repair any leaks.
   
5. Inspect the Fuel Filters for Contamination
A. Remove the fuel filters. Inspect the fuel filters for contamination. Contaminants in the fuel such as hydrogen sulfide and sulfur can lead to the formation of acids in the crankcase. Obtain a fuel analysis.
   
Fuel Filters
   
Result: The fuel has contamination.
Repair: Determine the cause of any contamination and make the necessary repairs.
Repair: Install new fuel filters. Refer to the Operation and Maintenance Manual.
   Contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts plate Mariner:

80633M
 
80633M PLATE, FRICTION
7010209, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716
83569M
 
83569M PLATE, BASE
7025208CW, 7028527, 7030200, 7030205, 7030320, 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716
84480M
 
84480M PLATE, TRANSOM
7040206, 7040207PW, 7048207, 7048227, 7048321, 7055324
19111M
PLATE, CLAMP BRACKET
19111M PLATE, CLAMP BRACKET
7025207PW, 7025208CW, 7025500, 7026226, 7030205, 7030301, 7030320, 7040206, 7040207PW, 7040208PW, 7040706, 7040716
97732M
 
97732M PLATE
7040202, 7040206, 7040706, 7040716
97736M
 
97736M PLATE
7040202, 7040206, 7040706, 7040716
17047M
 
17047M PLATE
7040206
814970M
 
814970M PLATE
7040706, 7040716
Back to top