35827 Mariner PLUG, BOTTOM COWL - SHORTING SWITCH HOLE

Illustration 1 g00293085
Fuel injection nozzle (1) Connection for the union nut of the fuel supply line (2) Threaded hole for the banjo bolt of the leak off line (3) Union nut on the fuel injection nozzle (4) Wire clip (5) Seat washer (1) Tighten the union nut of the high pressure fuel line (not shown) to the following torque: ... 22 N m (16 lb ft) (2) Tighten the banjo bolts for the leak off tubing (not shown) to the following torque: ... 9.0 N m (80 lb in) (3) Tighten the union nut on the fuel injection nozzle to the following torque: ... 30 N m (22 lb ft)Note: When the fuel injection nozzle is installed, put a 2.0 mm (0.08 inch) bead of 4C-5591 Anti-Seize Compound on the first two threads of the union nut. (4) Wire clip (5) Seat washerNote: Remove the original seat washer from the threaded hole for the fuel injection nozzle which is located in the cylinder head. If the original seat washer is not removed, the projection of the nozzle will be incorrect when a new seat washer is installed. Do not reuse seat washer (5) .Bench test the fuel injection nozzles at a temperature of 18 to 20 °C (64 to 70 °F).Note: Use clean SAE J-967 oil (ISO 4113) when you are conducting the test. The oil is available in 5 gallon containers ( 6V-6068 Calibration Fluid ) and 55 gallon containers ( 6V-6067 Calibration Fluid ). If dirty oil is used for the test, the components of the fuel injection nozzle will be damaged.Refer to the Systems Operations, Testing and Adjusting Module, "Fuel Injection Nozzle - Test" topic for additional information on testing the fuel injection nozzles.
Table 1
Service Settings For The Fuel Injection Nozzles    
Code (1)    Minimum and Maximum Pressure Settings    
"KB"     29570 to 30400 kPa (4290 to 4412 psi)    
"KC"     28570 to 29400 kPa (4145 to 4267 psi)    
"KD"     28570 to 29400 kPa (4145 to 4267 psi)    
"KE"     29070 to 29900 kPa (4220 to 4340 psi)    
"KF"     29070 to 29900 kPa (4220 to 4340 psi)    
"KG"     29570 to 30400 kPa (4290 to 4412 psi)    
"KH"     28570 to 29400 kPa (4145 to 4267 psi)    
"KJ"     24470 to 25300 kPa (3550 to 3672 psi)    
"KK"     29570 to 30400 kPa (4290 to 4412 psi)    
"KL"     29570 to 30400 kPa (4290 to 4412 psi)    
"KM"     29570 to 30400 kPa (4290 to 4412 psi)    
"KN"     28570 to 29400 kPa (4145 to 4267 psi)    
"KP"     29570 to 30400 kPa (4290 to 4412 psi)    
"KR"     28570 to 29400 kPa (4145 to 4267 psi)    
"KS"     28570 to 29400 kPa (4145 to 4267 psi)    
"KT"     28570 to 29400 kPa (4145 to 4267 psi)    
"KU"     28970 to 29800 kPa (4205 to 4325 psi)    
"KV"     24470 to 25300 kPa (3550 to 3672 psi)    
"KW"     28570 to 29400 kPa (4145 to 4267 psi)    
"NX"     28570 to 29400 kPa (4145 to 4267 psi)    
"NY"     28570 to 29400 kPa (4145 to 4267 psi)    
"NZ"     28570 to 29400 kPa (4145 to 4267 psi)    
"PA"     28570 to 29400 kPa (4145 to 4267 psi)    
"PB"     28570 to 29400 kPa (4145 to 4267 psi)    
"PC"     28570 to 29400 kPa (4145 to 4267 psi)    
"PD"     28570 to 29400 kPa (4145 to 4267 psi)    
"RZ"     24470 to 25300 kPa (3550 to 3672 psi)    
"SA"     24470 to 25300 kPa (3550 to 3672 psi)    
"SB"     24470 to 25300 kPa (3550 to 3672 psi)    
"SC"     24470 to 25300 kPa (3550 to 3672 psi)    
( 1 ) The code letters are stamped on the side of the fuel injector body. The code letters are located below the connection for the nut of the high pressure fuel line.Note: Ensure that the new fuel injection nozzles have the same identification code as the nozzles which were originally installed in the cylinder head.Leakage in 10 seconds ... 0 drops