849154T 1 PULLER ASSEMBLY Mariner
7031203GD, 7031207LF, 7031312TB, 7041203GB, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7055207HB, 7055207TF, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317U
PULLER
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$39.99
09-12-2023
US: The ROP Shop
zt truck parts Puller Assy Tool 91-849154T1 849154T1 Fit for Mercury Mariner Force
zt truck parts
zt truck parts
$42.99
08-12-2022
-: -
The ROP Shop | Flywheel Puller Tool for Mercury MerCruiser 91-849154T1, 91849154T1, 849154T1
The ROP Shop replacement Flywheel Puller Tool for Mercury MerCruiser 91-849154T1, 91849154T1, 849154T1 || Specs - Tool Thread Size: 1 1/2"-16 TPI. Bolt Thread Size: 5/8"-18 TPI. Refer to images 2 & 3 for more information || Includes - (1) Flywheel Puller, (1) Lifting Eye, (1) Puller Bolt & (1) Crankshaft Protector; comes as shown in the first image || Tool removes the flywheel from the crankshaft while protecting the crankshaft || Fits/For: Many Mercury, Mariner, Race, SportJet & Force outboard models. Please check that your motor has a 1 1/2"-16 thread size to ensure fitment
The ROP Shop replacement Flywheel Puller Tool for Mercury MerCruiser 91-849154T1, 91849154T1, 849154T1 || Specs - Tool Thread Size: 1 1/2"-16 TPI. Bolt Thread Size: 5/8"-18 TPI. Refer to images 2 & 3 for more information || Includes - (1) Flywheel Puller, (1) Lifting Eye, (1) Puller Bolt & (1) Crankshaft Protector; comes as shown in the first image || Tool removes the flywheel from the crankshaft while protecting the crankshaft || Fits/For: Many Mercury, Mariner, Race, SportJet & Force outboard models. Please check that your motor has a 1 1/2"-16 thread size to ensure fitment
$17.99
04-07-2022
-: -
A.A Flywheel Puller Lift Ring Replacement for Mercury Mariner Outboard 91-90455-1, 91-849154T1
Replaces Part #’s: 91-849154T1, 849154T1, 91-90455-1, 904551, 90455 || Includes: 1x Flywheel Puller, 1x Lift Ring, 1x Pusher Bolt, 1x Thread Protector || Specifications: 1 ½” – 16 TPI Tool Threads, 5/8” – 18 TPI Bolt Threads || For Use On: Most 45HP and up Mercury, MerCruiser, Mariner, Force and Yamaha outboard motors
Replaces Part #’s: 91-849154T1, 849154T1, 91-90455-1, 904551, 90455 || Includes: 1x Flywheel Puller, 1x Lift Ring, 1x Pusher Bolt, 1x Thread Protector || Specifications: 1 ½” – 16 TPI Tool Threads, 5/8” – 18 TPI Bolt Threads || For Use On: Most 45HP and up Mercury, MerCruiser, Mariner, Force and Yamaha outboard motors
Compatible models:
7031203GD
7031207LF
7031312TB
7041203GB
7043213HD
7043213TD
7043302TD
7043412TB
7043412TD
7050312TB
7050312UB
7050412TB
7050412TD
7050412UB
7055207HB
7055207TF
7075217HD
7075217TD
7075217UD
70752L7TF
70752L7UF
7075317TB
7075317UB
7075412TB
7075412UB
7075412UY
7090412TB
7090412TD
7090412TY
7090412UB
7090412UY
7100412HB
7115412TB
7135412JD
7135473KD
7135D73RD
7135D73UY
7135D73ZY
7150413LD
7150413RD
7150413UY
7150413ZY
7150423JD
7200413JD
7200413UY
7200413ZY
7200423UY
7200473KD
7200D73IY
7200D73MD
7200D73RD
7200D73ZY
7225413HD
7225E73MD
Mariner
Mariner entire parts catalog list:
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS(SPECIAL) » 849154T 1
- TOOLS » 849154T 1
- TOOLS-SPECIAL » 849154T 1
- TOOLS » 849154T 1
- TOOLS » 849154T 1
- TOOLS » 849154T 1
- TOOLS » 849154T 1
- TOOLS » 849154T 1
- TOOLS » 849154T 1
- TOOLS » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS-SPECIAL » 849154T 1
- TOOLS, SPECIAL » 849154T 1
- TOOLS » 849154T 1
- TOOLS » 849154T 1
- TOOLS » 849154T 1
- TOOLS-SPECIAL » 849154T 1
- TOOLS » 849154T 1
- TOOLS-SPECIAL » 849154T 1
- TOOLS » 849154T 1
- TOOLS » 849154T 1
- TOOLS-SPECIAL » 849154T 1
- TOOLS » 849154T 1
Information:
Table 1
Diagnostic Trouble Codes for Ether Injection
J1939 Code Code Description Comments
626-5 Ether Injection Control Solenoid : Current Below Normal The Electronic Control Module (ECM) detects the following conditions:
A low current condition in the output from the ECM to the solenoid for ether injection
The ECM has been powered for at least 2 seconds.
If equipped, the warning lamp will come on. The ECM will log the diagnostic code.
626-6 Ether Injection Control Solenoid : Current Above Normal The Electronic Control Module (ECM) detects the following conditions:
A high current condition in the output from the ECM to the solenoid for ether injection
The ECM has been powered for at least 2 seconds.
If equipped, the warning lamp will come on. The ECM will log the diagnostic code. If there is an active engine shutdown, the ether injection system is disabled . The ether system will be disabled if the glow plugs have been activated in the last 5 minutes.Activation of the ether starting aid is based on the minimum temperature from one of the following temperature sensors:
Intake manifold temperature sensor
Air intake temperature sensor
Coolant temperature sensorRefer to Illustration 1.
Illustration 1 g06396017The following conditions must be met for the ether injection system to be enabled:
Ether injection is set to "Enabled" in the ECM parameters
The lower of the intake manifold air temperature, the air inlet temperature, or the coolant temperature is less than the activation point for ether start aid. Refer to Illustration 1.
The maximum temperature of the intake manifold air temperature sensor, the air inlet temperature sensor, or the coolant temperature sensor is below 50° C (122° F).During the following procedure, refer to the electrical schematic for the application.Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Remove the electrical power from the ECM.
B. Thoroughly inspect the connector for the ether injection solenoid. Refer to Troubleshooting, "Electrical Connectors - Inspect".
C. Perform a 30 N (6.7 lb) pull test on each of the wires in the ether solenoid connector.
D. Check the harness and the wiring for abrasion and for pinch points.
Note: Do not disconnect the ECM connector at this stage. The ECM can only be disconnected and reconnected 10 times before damage to the harness connector may occur.
Loose connection or damaged wire
Result: The harness and wiring are OK.
Proceed to Test Step 2.
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Proceed to Test Step 4.
2. Check the Wiring Between the ECM and the Ether Control
The ether canister must be removed prior to performing this procedure.
A. Verify that the keyswitch is in the OFF position.
B. Remove the ether canister.
C. Disconnect the engine harness connector for the ether control.
D. Connect a digital voltmeter across the two terminals on the engine harness connector for ether control.
E. Turn the keyswitch to the ON position.
F. Measure the voltage across the terminals while the keyswitch is turned ON.
10 VDC
Result: The voltage measured 0 VDC.
Repair: There is a problem in an electrical component between the ECM and the harness connector for the ether control. The problem may be inside an electrical connector. Make the necessary repairs.
Proceed to Test Step 3.
Result: The voltage measured greater than 10 VDC.
The electrical components between the ECM and the harness connector for the ether control are OK.
Proceed to Test Step 3.
3. Measure the Resistance of the Coil Inside the Ether Control
A. Verify that the ether control is not connected to the engine harness.
B. Measure the resistance of the coil inside the ether control.
20 Ohms
Result: The measured resistance was approximately 20 Ohms.
Proceed to Test Step 4.
Result: The measured resistance was not approximately 20 Ohms.
Repair: Replace the ether control.
Proceed to Test Step 4.
Illustration 2 g03152796
Ether solenoid activation pin
Table 3
Troubleshooting Test Steps Values Results
4. Verify the Repair
A. Activate the Ether Injection Override.
B. Verify that the plunger moved up when the override was active.
Plunger movement
Result: The plunger moved up when the override was active.
Install the ether bottle and return the unit to service.
If the procedure did not correct the issue, contact the Dealer Solutions Network (DSN).
Parts puller Mariner:
27780
27780 PULLER
7004201HB, 7004201UB, 70152374D, 7020201HB, 7020201TB, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7055207GD, 7055207H
29310
29310 PULLER PLATE
7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7055207GD, 7055207HB, 7055207TF, 7115473JD, 7135412ED, 7135412HD, 7135412J
46086A 1
46086A 1 PULLER JAWS
70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7055207GD, 7055207HB, 7055207TF, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412T
816242
816242 PULLER JAWS
7115473JD, 7135412ED, 7135412HD, 7135412JD, 7135473GD, 7135473HD, 7135473KD, 7135D73RD, 7135D73UY, 7135D73ZY, 7150413ED, 7150413HD, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7150423JD, 7175423HD, 7200413JD, 7200413UY, 7200413ZY, 7200423UY, 7200473G
85716
85716 PULLER TOOL
70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7115473JD, 7115F13KD, 7115F13RD, 7115F13UF, 7135412ED, 7135412HD, 7135412JD, 7135473GD, 7135473HD, 7135473KD, 7135D73RD, 7135D73U
83165T
83165T PULLER ASSEMBLY
7004201HB, 7004201UB, 7006201HB, 7006201TB, 7010207HB, 7011201TB, 7015201LD, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7055207HB, 7055207TF, 7075217HD, 7075217TD, 7075217UD, 70752L7T
853996
853996 PULLER ASSEMBLY TOOL, Flywheel
7015203KL, 7025207UL, 7025217UL, 7030201KL, 7030201UL, 7030211U2, 7030A01UL, 7030A11UL, 7031207LF
853996 20
853996 20 PULLER KIT, Needle Roller Bearing
7006201MK, 7006201UK, 7015203KL, 7015203UL, 7025207UL, 7025217UL, 7030201KL, 7030201UL, 7030211U2, 7030A01UL, 7030A11UL, 7031207LF