16840A 2 Mariner REMOTE CONTROL ATTACHING KIT


16840A 2 REMOTE CONTROL ATTACHING KIT Mariner 7004201HB, 7004201UB, 7004211SK REMOTE
16840A 2 REMOTE CONTROL ATTACHING KIT Mariner
Rating:
93

Buy REMOTE CONTROL ATTACHING KIT 16840A 2 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Mariner entire parts catalog list:

7004201HB 1999,2000,2001,2002,2003,2004,2005
7004201UB 2006
7004211SK 1990,1991,1992,1993,1994,1996,1997,1998

Information:

INSTALL HYDRAMECHANICAL SHUTOFF CONTROL
1. Install coupling (2) on the end of the shutoff drive gear.2. Put hydramechanical shutoff control (1) and the gasket in position on the shutoff drive housing assembly. Make sure the shaft of the shutoff control is correctly engaged with the coupling and install the bolts to hold the shutoff control in position.3. Connect tube assemblies (3), (4) and (5) to the shutoff control.4. Put clean engine oil on the O-ring seals and install tube (6) in the bottom of the shutoff control. Put cover (7) and the diverter valve as a unit in position on tube (6) and the shutoff drive housing assembly. Install the bolts to hold these in position.5. Connect tube assemblies (8) to the shutoff control and connector tube assemblies (9) to the diverter valve. DISASSEMBLE HYDRAMECHANICAL SHUTOFF CONTROL
start by:a) remove hydramechanical shutoff control1. Remove the bolts and remove actuator valve (1) from the pressure control valve.
CAUTION There is spring pressure on cover (2).
2. Remove the bolts and remove cover (2) from the actuator valve body.3. Remove springs (4), spacer (5) and valve assemblies (3) from the valve body.4. Remove tube assembly (7) from the shutoff control.5. Remove pressure control valve (6) from the shutoff control.6. Put identification marks on valve assemblies (12) and (13) for assembly purposes. Remove rack shutoff valve (12) and air inlet shutoff valve (13) from the pressure control body assembly. Remove three O-ring seals from each valve.7. Remove plug (11) to remove pilot valve (10) and spring (9) from the pressure control body assembly.8. Remove manual shutoff valve (8) as a unit from the pressure control body assembly. 9. Loosen nut (16) to remove knob (17) and nut (16) from valve (14). Remove adapter (18) and spring (19) from valve (14). Remove O-ring seal (15) from adapter (18).10. Remove seal (20) from adapter (18).11. Remove eight bolts (22) to remove gerotor pump group (21) from the shutoff control housing assembly.12. Use tool (A) to remove ring (24) and the washer from the carrier assembly shaft. Do not remove bolts (23) at this time.13. Remove carrier assembly (25) from the gerotor pump group. 14. Remove dowels (27) to remove weights (26) from carrier (25). Remove pin (28) and use a press to remove shaft (29) from carrier (25).15. Remove washer (30) from the pump group.16. Remove the two bolts (23) to remove cover assembly (31) from the plate.17. Remove gasket (32) from the plate. 18. Remove plate (33) from the housing assembly. 19. Remove seal (34) from plate (33). Carefully remove driven gear (36) from sleeve (35) so brush (39) and spring (38) do not become lost.20. To remove the gerotor assembly, remove drive gear (37), driven gear (36) and sleeve (35) from the housing assembly.21. Remove brush (39) and spring (38) from driven gear (36).22. Use tool (B) to remove snap ring (43) and remove seat (42), spring (41) and plunger assembly (40) from the housing assembly.23. Remove O-ring seal (44) from the housing assembly. 24. Remove speed sensing valve (46), spring (45) and the seat from the housing assembly guide.25. Remove ring (50) to remove race (49), bearing (51) and race (48) from seat (52). Loosen nut (47) to remove seat (52) and nut (47) from speed sensing valve (46).26. Remove shaft (53) to remove lever (54) from the housing assembly.27. Remove the wire seal and bolts (55) to remove cover (56), the two seats and the spring from the housing assembly.28. Use tool group (C) to remove the guide from the housing assembly. ASSEMBLE HYDRAMECHANICAL SHUTOFF CONTROL
1. If necessary, make a replacement of dowels (2) and make sure they are 3.0 0.5 mm (.118 .020 in.) above the surface of the housing assembly.2. Put guide (1) in position in the housing assembly and make sure the dash mark on the end of the guide is in alignment with hole (3). Use tool group (A) to install guide (1) in the housing assembly.3. Put lever (5) in position in the housing assembly as shown and install shaft (4) to hold lever (5) in position. Make sure the end of the shaft is even (flush) 0.25 (.010 in.) with the housing assembly.4. Put the seat, spring (7) and seat (6) in position in cover (8) and put cover (8) and the gasket in position on the housing assembly. Install the bolts to hold the cover in position.5. Install nut (15) and seat (10) on speed sensing valve (9). Make sure the dimension between the end of the valve and the nut face of the seat is 117.21 0.25 mm (4.614 .010 in.) and tighten the nut. Put race (14), bearing (11) and race (13) in position on seat (10) and install ring (12) to hold these in position. 6. Install seat (16), spring (17) and speed sensing valve (9) on the housing assembly guide.7. Put clean engine oil on O-ring seal (18) and put O-ring seal (18), plunger assembly (19), spring (20) and seat (21) in position in the housing assembly. Use tool (B) to install snap ring (22) to hold the plunger assembly, the spring and seat in position.8. If necessary, make a replacement of pin (24) and make sure pin (24) is 3.96 0.50 mm (.156 .020 in.) above the bottom surface of the bore.9. Install the gerotor assembly as follows:a) Install sleeve (23) and make sure the groove (slot) on sleeve (23) is in alignment with pin (24).b) Put the spring and brush (26) in position in the driven gear (25). Install driven gear (25) in the sleeve.c) Install drive gear (27) in the driven gear.


Back to top