80609M Mariner RETAINER, CHECK VALVE


80609M RETAINER, CHECK VALVE Mariner 7015207, 7015307, 7015327, 7028207, 7028527, 7040207, 7040507, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528 RETAINER
80609M RETAINER, CHECK VALVE Mariner
Rating:
68

Buy RETAINER, CHECK VALVE 80609M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

Mariner entire parts catalog list:

7015207 1977
7015307 1977
7015327 1987
7028207 1977
7028527 1977
7040207 1977
7040507 1987
7048207 1977
7048227 1977
7048321 1981
7055324 1984,1985,1988,1989
7055524 1984,1985
7060507 1977
7060522 1982
7060528 1978

Information:


Illustration 1 g01139787
(1) Thickness of the top plates ... 8.585 0.025 mm (0.3380 0.0010 inch) (2) Tighten the three studs to the following torque. ... 35 5 N m (26 4 lb ft) (3) Tighten the studs on top of the cylinder block to the following torque. ... 35 5 N m (26 4 lb ft) (4) There are two plugs on the front of the cylinder block. There are two plugs on the rear of the cylinder block. Apply 5P-3413 Pipe Sealant on the threads of the plugs before assembly. (5) The gasket that is between the cylinder block and the top plates is the following thickness. ... 0.208 0.025 mm (0.0082 0.0010 inch) (6) The dowels extend from the cylinder block. Distance ... 18.5 0.5 mm (0.73 0.02 inch) (7) Put 5P-3413 Pipe Sealant on the threads of the plugs before assembly. Tighten the plug that is in the front of the block and tighten the plug that is in the rear of the block to the following torque. ... 80 15 N m (60 11 lb ft) (8) Bore in the cylinder block for the camshaft bearings ... 76.835 0.018 mm (3.0250 0.0007 inch) (9) Bore in cylinder block for main bearings New bearings that are standard size ... 129.891 0.013 mm (5.1138 0.0005 inch) Bearings that are 0.64 mm (0.025 inch) larger than the standard size ... 130.526 0.013 mm (5.1388 0.0005 inch) (10) There are two dowels that are in the front of the cylinder block. There are two dowels that are in the rear of the cylinder block. The dowels project from the cylinder block. Distance ... 19.0 0.5 mm (0.75 0.02 inch) (11) The width of the slot for the main bearing caps is the following value. ... 215.900 0.013 mm (8.5000 0.0005 inch)Width of main bearing cap ... 215.900 0.025 mm (8.5000 0.0010 inch) (12) Use the procedure that follows to install the main bearing caps.
Illustration 2 g00285128
Marks For Tightening Main Bearings
Apply 4C-5593 Anti-Seize Compound on the threads of the bolts.
Tighten the bolts first on the bearing tab side of the cap.Torque for bolts ... 258 14 N m (190 10 lb ft)
Tighten the bolts that are opposite the bearing tab side of the cap.Torque for bolts ... 258 14 N m (190 10 lb ft)
Put a mark on each bolt and each cap.
Tighten the bolts that are opposite the bearing tab side of the cap from the mark to the following value.Angle from the mark. ... 120 5 degrees
Tighten the bolts on the bearing tab side of the cap from the mark to the following value.Angle from the mark. ... 120 5 degrees
Illustration 3 g00839257
(13) The distance from the centerline of the crankshaft bearing bore to the top of the cylinder block is the following value. ... 419.10 0.15 mm (16.500 0.006 inch) (14) The distance from the centerline of the crankshaft bearing bore to the bottom of the cylinder block is the following value. ... 165.10 0.10 mm (6.500 0.004 inch)


Parts retainer Mariner:

20430
 
20430 RETAINER
7005201, 7005207, 7005227, 7008204, 7008208, 7008226, 7008238, 7008247, 7008248, 7008305, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7040202, 7040206, 70402
81191M
 
81191M RETAINER, CHOKE LEVER
7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008226, 7020201, 7025200, 7025207NW, 7025207PW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207, 7040207PW, 7040208, 7040328, 7040507, 7040706, 7
81047M
RETAINER, MAGNETO BASE...
81047M RETAINER, MAGNETO BASE...
7008208, 7008238, 7008247, 7008248, 7015207
80626M
84770M
 
84770M RETAINER, THROTTLE ROD
7028527, 7030200, 7030205, 7030320
84787M
 
84787M RETAINER, SHIFT SHAFT
7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7030205, 7030320
82678M
 
82678M RETAINER, BASE ASS'Y
7048227, 7048321, 7055324, 7055524, 7060507
84433M
RETAINER, LOWER MOUNT
84433M RETAINER, LOWER MOUNT
7055524, 7060507, 7060522, 7060528
Back to top