814489M Mariner RIVET

Table 1
Cross-Reference from CID-FMI Code on Cat Data Link to Troubleshooting Procedure
Code and Description Procedure
1-5 Cylinder #1 Injector current below normal Troubleshooting, "Injector Solenoid - Test"
1-6 Cylinder #1 Injector current above normal
2-5 Cylinder #2 Injector current below normal
2-6 Cylinder #2 Injector current above normal
3-5 Cylinder #3 Injector current below normal
3-6 Cylinder #3 Injector current above normal
4-5 Cylinder #4 Injector current below normal
4-6 Cylinder #4 Injector current above normal
5-5 Cylinder #5 Injector current below normal
5-6 Cylinder #5 Injector current above normal
6-5 Cylinder #6 Injector current below normal
6-6 Cylinder #6 Injector current above normal
41-3 8 Volt DC Supply voltage above normal Troubleshooting, "Sensor Supply - Test"
41-4 8 Volt DC Supply voltage above normal
91-8 Throttle Position Sensor abnormal frequency, pulse width, or period Troubleshooting, "Speed Control - Test"
94-3 Fuel Delivery Pressure Sensor voltage above normal Troubleshooting, "Sensor Signal (Analog, Active) - Test"
94-4 Fuel Delivery Pressure Sensor voltage below normal
100-3 Engine Oil Pressure Sensor voltage above normal
100-4 Engine Oil Pressure Sensor voltage below normal
100-10 Engine Oil Pressure Sensor abnormal rate of change
110-3 Engine Coolant Temperature Sensor voltage above normal Troubleshooting, "Sensor Signal (Analog, Passive) - Test"
110-4 Engine Coolant Temperature Sensor voltage below normal
168-0 Electrical System Voltage high - most severe (3) Troubleshooting, "Electrical Power Supply - Test"
168-1 Electrical System Voltage low - most severe (3)
168-2 Electrical System Voltage erratic, intermittent, or incorrect
172-3 Intake Manifold Air Temperature Sensor voltage above normal Troubleshooting, "Sensor Signal (Analog, Passive) - Test"
172-4 Intake Manifold Air Temperature Sensor voltage below normal
174-3 Fuel Temperature Sensor voltage above normal
174-4 Fuel Temperature Sensor voltage below normal
190-8 Engine Speed Sensor abnormal frequency, pulse width, or period Troubleshooting, "Speed/Timing - Test"
247-9 SAE J1939 Data Link abnormal update rate Troubleshooting, "CAN Data Link - Test"
253-2 Personality Module erratic, intermittent, or incorrect Troubleshooting, "ECM Software - Install"
261-11 Engine Timing Offset fault Troubleshooting, "Timing - Calibrate"
261-13 Engine Timing Calibration calibration required
262-3 5 Volt Sensor DC Power Supply voltage above normal Troubleshooting, "Sensor Supply - Test"
262-4 5 Volt Sensor DC Power Supply voltage below normal
268-2 Programmed Parameter Fault erratic, intermittent, or incorrect Troubleshooting, "Configuration Parameters"
274-3 Atmospheric Pressure Sensor voltage above normal Troubleshooting, "Sensor Signal (Analog, Active) - Test"
274-4 Atmospheric Pressure Sensor voltage below normal
342-8 Secondary Engine Speed Sensor abnormal frequency, pulse width, or period Troubleshooting, "Speed/Timing - Test"
1690-8 Throttle #2 Position Sensor abnormal frequency, pulse width, or period
1785-3 Intake Manifold Pressure Sensor voltage above normal Troubleshooting, "Sensor Signal (Analog, Active) - Test"
1785-4 Intake Manifold Pressure Sensor voltage below normal
1785-10 Intake Manifold Pressure Sensor abnormal rate of change Diagnostic Codes
Diagnostic codes alert the operator that a problem in the electronic system has been detected. Diagnostic codes are also used by the service technician to identify the nature of the problem. Caterpillar Electronic Technician (ET) is a software program that is designed to run on a personal computer. The software can be used by the service technician in order to view the diagnostic code information for an ECM. Diagnostic codes may consist of the component identifier (CID), and the failure mode identifier (FMI).Component Identifier (CID) - The CID indicates the component that generated the code. For example, the CID number 1 identifies the fuel injector for the number one cylinder.Failure Mode Identifier (FMI) - The FMI indicates the type of failure.Refer to Table 1 for a complete list of the diagnostic codes and the appropriate troubleshooting procedure.Note: Do not confuse diagnostic codes with event codes. Event codes alert the operator that an abnormal operating condition such as low oil pressure or high coolant temperature has been detected. If an event code is active, refer to Troubleshooting, "Event Code List".Illustration 1 is an example of the operating range of a sensor.
Illustration 1 g01365757
Example of the typical operating range of a sensor
(1) This area represents the normal operating range of the engine parameter.
(2) In these areas, the engine is operating in an unsafe operating range of the monitored parameter. An event code will be generated for the monitored parameter. The sensor circuit does not have an electronic problem. Refer to Troubleshooting, "Event Code List" for additional information on event codes.
(3) In these areas, the signal from the sensor is outside of the operating range of the sensor. The sensor circuit has an electronic problem. A diagnostic code will be generated for the sensor circuit. Active Diagnostic Codes
An active diagnostic code represents a problem with the electronic control system. Correct the problem as soon as possible.When the engine's ECM generates an active diagnostic code, the "Active Alarm" indicator ("Engine Control Alarm Status" on Cat ET) is activated in order to alert the operator. If the condition that generated the code is momentary, the message disappears from the list of active diagnostic codes. The diagnostic code becomes logged.Logged Diagnostic Codes
When the ECM generates a diagnostic code, the ECM logs the code in permanent memory. The ECM has an internal diagnostic clock. Each ECM will record the following information when a code is generated:
The hour of the first occurrence of the code
The hour of the last occurrence of the code
The number of occurrences of the codeThis information is a valuable indicator for troubleshooting intermittent problems.A code is cleared from memory when one of the following conditions occur:
The service technician manually clears the code.
The code does not recur for 100 hours.
A new code is logged and there are already ten codes in memory. In this case, the oldest code is cleared.Some diagnostic codes may be easily triggered. Some diagnostic codes may log occurrences that did not result in complaints. The most likely cause of an intermittent problem is a faulty connection or damaged wiring. The next likely cause is a component failure. The least likely cause is the failure of an electronic module. Diagnostic codes that are logged repeatedly may indicate a problem that needs special investigation.Note: Always clear logged diagnostic codes after investigating and correcting the problem which generated the code.