47837 Mariner ROD END, PUSH ROD


47837 ROD END, PUSH ROD Mariner 7050200, 7050716, 7070509, 7070520 ROD
47837 ROD END, PUSH ROD Mariner
Rating:
78

Buy ROD END, PUSH ROD 47837 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 27
 

Compatible models:

Mariner entire parts catalog list:

7050200 1980,1982,1983,1985,1986
7050716 1986
7070509 1979
7070520 1980,1982,1983

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 238-9586 Camshaft Drive Group 1
C 125-0200 Camshaft Pilot As 2
D 125-0201 Camshaft Guide As 1
E 8T-3169 Crank As 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The following steps are for the installation of a camshaft in the 3512C Engines. The camshaft is in two pieces. Note: Ensure that the camshafts are assembled and installed according to the marks on the ends of the camshafts.
Illustration 1 g01053512
Install Tooling (D) on the flywheel housing. Do not tighten the bolts on Tooling (D).
Install Tooling (C) on the end of the front half of the camshaft.
Ensure that the camshaft and the camshaft bearings are clean. Place clean engine oil on the lobes and the journals of the camshaft. Also place clean engine oil on the camshaft bearings.
Attach a suitable lifting device to the camshaft. The weight of one-half of the camshaft for 3512C Engines is approximately 36 kg (80 lb).
Position the front half of camshaft (12) in the engine until Tooling (C) is in the first camshaft bearing.
Rotate camshaft (12) and tighten the bolts for Tooling (D).
Rotate camshaft (12) and insert the camshaft until the camshaft is slightly protruding from Tooling (D).
Illustration 2 g00914670
Illustration 3 g00914462
If the dowel was removed from the front half of camshaft (12), install the dowel. Install the dowel to 22 0.5 mm (0.9 0.02 inch) from the surface of the camshaft.
Attach a suitable lifting device to rear half of camshaft (13). The weight of one-half of the camshaft for 3512C Engines is approximately 36 kg (80 lb). Install spacer (15) and the rear half of camshaft (13) onto the front half of camshaft (12). Install bolts (14) and tighten to a torque of 55 7 N m (41 5 lb ft).
Install Tooling (C) and Tooling (E) on the rear half of camshaft (13).
Rotate the rear half of camshaft (13) and insert the camshaft into the engine.
Remove all Tooling. Repeat Steps 1.a through 1.k for the camshaft on the opposite side of the engine. Go to Step 2.
Illustration 4 g00914691
Install thrust washers (10) and bolts (9) that fasten the camshaft to the engine.
If the camshaft is out of time more than 18 degrees (approximately 1/2 of the timing pin is out of the groove), the valves can make contact with the pistons. This will cause damage to the engine. Refer to Testing and Adjusting, "Camshaft Timing" for more information.
Illustration 5 g00914693
Remove timing pin (16) from the storage position on the side of the engine.
Turn the camshaft until timing pin (16) can be installed through the cylinder block and into groove (17) that is in the camshaft.
Repeat Steps 3 and 4 for the camshaft on the opposite side of the engine.
Illustration 6 g00914707
Illustration 7 g01053668
Remove bolts (19), cover (18), and plug (20).
Install one bolt (19) into the flywheel housing through the hole for plug (20). Use Tooling (A) and a ratchet to turn the flywheel until bolt (19) can be installed through the hole and into the flywheel. Doing so will position the No. 1 cylinder at the top center. Refer to Testing and Adjusting, "Finding the Top Center Position for the No. 1 Piston" for more information.
Illustration 8 g00914726


Parts rod Mariner:

47835
47836
 
47836 ROD, PUSH - REVERSE LOCK (LONG SHAFT)
7050200, 7050716, 7070509, 7070520
74164
 
74164 ROD, LINK-THROTTLE
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
74212
 
74212 ROD, LINK-SPARK ADVANCE
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
48419
 
48419 ROD END, SHIFT ROD
7045217, 7050200, 7050302ED, 7050412YD, 7050716, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075312ND, 7075312SD, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7075717, 70904
Back to top