81348M Mariner ROD, CONTROL


81348M ROD, CONTROL Mariner 7002200, 7048207, 7048227, 7048321, 7060507, 7060528 ROD
81348M ROD, CONTROL Mariner
Rating:
68

Buy ROD, CONTROL 81348M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 42
 

Compatible models:

Mariner entire parts catalog list:

7002200 1980,1985,1988,1989
7048207 1977
7048227 1977
7048321 1981
7060507 1977
7060528 1978

Information:


Table 1
Diagnostic Codes Table for Sensor Calibration
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
3358-13 3385-13 Engine Exhaust Gas Recirculation Inlet Pressure : Out of Calibration The ECM detects the following conditions:
The offset between the NRS inlet pressure and the barometric pressure is outside the acceptable range during initialization check.
The offset between the NRS inlet pressure and the barometric pressure is outside the acceptable range during sensor calibration when the engine is not running.
The warning lamp will come on and the engine will derate. The code is logged.
3563-13 1785-13 Engine Intake Manifold #1 Absolute Pressure : Out of Calibration The ECM detects the following conditions:
The offset between the intake manifold air pressure and the barometric pressure is outside the acceptable range during initialization check.
The offset between the intake manifold air pressure and the barometric pressure is outside the acceptable range during sensor calibration with the engine not running.
The warning lamp will come on and the engine will derate.
The code is logged.
5019-13 3511-13 EGR Outlet Pressure : Out of Calibration The ECM detects the following conditions:
The offset between the NRS outlet pressure and the barometric pressure is outside the acceptable range during initialization check.
The offset between the NRS outlet pressure and the barometric pressure is outside the acceptable range during sensor calibration with the engine not running.
The warning lamp will come on and the engine will derate.
The code is logged. The Electronic Control Module (ECM) checks the signals from certain pressure sensors 12 seconds after the keyswitch is turned to the OFF position. The key must remain in the OFF position for a further 2 seconds in order for the ECM to check the signals from the sensors. During this time, the ECM compares the signal from the barometric pressure sensor with the signal from the following pressure sensors:
Intake manifold air pressure
NRS inlet pressure
NRS outlet pressureThe sensor signal must be within the specified range of the signal from the reference pressure sensor. If a sensor signal is out of the range, the corresponding fault code becomes active.The offset value is stored in the engine ECM. If the requirements are not met for the offset to be checked against the barometric pressure sensor, the stored value is used.
Table 2
Troubleshooting Test Steps Values Results
1. Check For Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Download the "Product Summary Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.
D. Use the electronic service tool to check that coolant temperature, intake manifold air temperature, and NRS temperature are all at least 5° C (41° F).
Note: Wait at least 10 seconds in order for the diagnostic codes to become active.
E. Use the electronic service tool to monitor active diagnostic codes or recently logged diagnostic codes. Look for an active or logged -3 or -4 codes for the pressure sensor or the barometric pressure sensor.
F. Use the electronic service tool to monitor active diagnostic codes or recently logged diagnostic codes. Look for an active or logged -13 code for a pressure sensor or the barometric pressure sensor.
G. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: There are no active diagnostic codes for the pressure sensors.
Repair: If there are logged diagnostic codes for the intake manifold pressure sensor, the fault may be intermittent.
Refer to Troubleshooting, "Electrical Connectors - Inspect" to identify intermittent faults.
Result: One or more of the temperature sensors is reading less than 5° C (41° F).
Proceed to Test Step 2.
Result: There is an active -3 or -4 diagnostic code for a pressure sensor or the barometric pressure sensor.
Repair: Troubleshoot these codes before continuing with this procedure.
Result: 3358-13 (3385-13) and 3563-13 (1785-13) diagnostic codes are active.
Proceed to Test Step 3.
Result: There is


Parts rod Mariner:

81408M
 
81408M ROD, SHIFT - LOWER
7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
81338M
 
81338M ROD, CHOKE
7048207, 7048227, 7048321, 7055324
81339M
 
81339M ROD, CHOKE LINK
7048207, 7048227
82988M
 
82988M ROD, CHOKE LINK
7040202, 7040206, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
82911M
 
82911M ROD, THROTTLE LEVER
7048207, 7048227, 7048321, 7060507, 7060528
81398M
92653M
 
92653M ROD, REVERSE LOCK (E)
7055524, 7060507, 7060522
81399M
 
81399M ROD, REVERSE LOCK (LONG SHAFT)
7055524, 7060507, 7060522, 7060528
Back to top