83545M Mariner ROD, MAGNETO CONTROL


83545M ROD, MAGNETO CONTROL Mariner 7040207, 7040507 ROD
83545M ROD, MAGNETO CONTROL Mariner
Rating:
103

Buy ROD, MAGNETO CONTROL 83545M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Compatible models:

7040207   7040507   Mariner

Mariner entire parts catalog list:

7040207 1977
7040507 1987

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g03345311
Typical example
Loosen hose clamp (2) and hose clamp (4) for hose assembly (1).
Disconnect hose assembly (1) from air inlet connection (3) and crankcase breather canister (8).
Loosen hose clamp (5) and hose clamp (7) (not shown) for hose assembly (6).
Disconnected hose assembly (11) (not shown) from crankcase breather canister (8).
Remove bolts (9) from crankcase breather canister (8).
Remove crankcase breather canister (8) and hose assembly (6) from bracket (10).
Remove hose assembly (6) from crankcase breather canister (8).
If necessary, disassemble the crankcase breather canister. Refer to Operation and Maintenance Manual, "Crankcase Breather (Canister) - Replace" for the correct procedure.
Illustration 2 g03345734
Follow Step 9.a through Step 9.g in order to disassemble valve mechanism cover (15).
Remove valve mechanism cover (15). Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure.
Remove bolts (12) from breather adapter (13).
Remove breather adapter (13) from valve mechanism cover (15).
Remove gasket (14).
Remove screws (18) and carefully remove baffle plate. (19).
Remove gauze (17) from valve mechanism cover (15).
If necessary, remove blanking plug (16) from valve mechanism cover (15). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 247-5377 Torque Wrench 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Make sure that the components of the breather assembly are installed correctly. Engine damage may occur if the breather assembly is not working properly.
Illustration 3 g03345734
Clean all parts and inspect all parts. Replace any parts that are worn or damaged. Ensure that the cavity for the breather in valve mechanism cover (12) is clean and free from restriction.
If necessary, follow Step 2.a through Step 2.j in order to assemble valve mechanism cover (15).
Install gauze (17) to valve mechanism cover (15).
Position baffle plate (19) into valve mechanism cover (15).
Install screws (18) to baffle plate (19).
Tighten screws (18) to a torque of 1.5 N m (13 lb in).
If necessary, install a new blanking plug (16) to valve mechanism cover (15). Tighten blanking plug to a torque of 20 N m (177 lb in).
Position a new gasket (14) onto valve mechanism cover (15).
Position breather adapter (13) onto valve mechanism cover (15).
Install bolts (12) to breather adapter (13).
Tighten screws (12) to a torque of 1.5 N m (13 lb in).
Install valve mechanism cover (12). Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure.
Illustration 4 g03345311
Typical example
If necessary, assemble the crankcase breather canister. Refer to Operation and Maintenance Manual, "Crankcase Breather (Canister) - Replace" for the correct procedure.
Install hose assembly (6) onto crankcase breather canister (8). Ensure that hose clamp (5) and hose clamp (7) are correctly orientated.
Position crankcase breather canister (8) and hose assembly (6) onto bracket (10). Ensure hose assembly (6) is correctly installed onto the connection on the valve mechanism cover.
Install bolts (9) to crankcase breather canister (8) hand tight.
Connected hose assembly (11) (not shown) to crankcase breather canister (8).
Tighten bolts (9) to a torque of 10 N m (89 lb in).
Securely tighten hose clamp (5) and hose clamp (7) (not shown) for hose assembly (6).
Connect hose assembly (1) to air inlet connection (3) and crankcase breather canister (8).
Securely tighten hose clamp (2) and hose clamp (4) for hose assembly (1).


Parts rod Mariner:

83468M
 
83468M ROD, LOCK
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716
83532M
 
83532M ROD
7040207, 7040208, 7040328, 7040507
83542M
 
83542M ROD, SHIFT
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716
83358M
 
83358M ROD, CHOKE LINK
7040207, 7040208, 7040328, 7040507
83595M
 
83595M ROD
7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716
83921M
ROD
83921M ROD
7025208CW, 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716, 7060522
83554M
 
83554M ROD
7040207, 7040507
Back to top