92655M Mariner ROD, LINK


92655M ROD, LINK Mariner 7055524, 7060507, 7060522 ROD
92655M ROD, LINK Mariner
Rating:
78

Buy ROD, LINK 92655M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 28
 

Compatible models:

Mariner entire parts catalog list:

7055524 1984,1985
7060507 1977
7060522 1982

Information:


Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g06146962
Remove bolts (4) and remove cooler (3) from exhaust gas recirculation valve assembly (1). Ensure that the tube assemblies on the cooler are not strained as the exhaust gas recirculation valve assembly is removed.
Remove gasket (5).
Remove O-ring seal (6) (not shown) from exhaust gas recirculation valve assembly (1).
Remove differential pressure and absolute pressure sensor (2) from exhaust gas recirculation valve assembly (1). Refer to Disassembly and Assembly, Pressure Sensor (Cooled Exhaust Gas) - Remove and Install for the correct procedure.Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - International Products P-80 Emulsion Rubber Assembly Lubricant 1
Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 2 g06146962
Ensure that the gasket surfaces of exhaust gas recirculation valve assembly (1) and cooler (3) are clean and free from damage.
Install differential pressure and absolute pressure sensor (2) to exhaust gas recirculation valve assembly (1). Refer to Disassembly and Assembly, Pressure Sensor (Cooled Exhaust Gas) - Remove and Install for the correct procedure.
Install a new gasket (5) to cooler (3).
Use Tooling (A) to lubricate a new O-ring seal (6) (not shown). Install the O-ring seal to exhaust gas recirculation valve assembly (1).
Install cooler (3) to exhaust gas recirculation valve assembly (1). Ensure that the tube assemblies on the cooler are not strained as the exhaust gas recirculation valve assembly is installed.
Install bolts (4) to exhaust gas recirculation valve assembly (1). Hand tighten the bolts.
Install the exhaust cooler for the NOx Reduction System (NRS) Disassembly and Assembly, Exhaust Cooler (NRS) - Remove and Install for the correct procedure.
After the installations of the exhaust cooler assembly, tighten bolts (4) to a torque of 22 N m (195 lb in). Ensure that the tube assemblies of the exhaust cooler are not strained as the bolts are tightened.
If a new EGR valve is install, use the electronic service tool to perform the "EGR Valve Replacement Reset". Refer to Troubleshooting, "Service Tool Features" for more information.
Use the electronic service tool to perform the "Air Systems Motor Valve Verification Test". Refer to Troubleshooting, "Service Tool Features" for more information.


Parts rod Mariner:

83921M
ROD
83921M ROD
7025208CW, 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716, 7060522
81408M
 
81408M ROD, SHIFT - LOWER
7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
82988M
 
82988M ROD, CHOKE LINK
7040202, 7040206, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
82911M
 
82911M ROD, THROTTLE LEVER
7048207, 7048227, 7048321, 7060507, 7060528
81397M
 
81397M ROD, REVERSE LOCK
7048207, 7048227, 7048321, 7060507, 7060522, 7060528
81348M
 
81348M ROD, CONTROL
7002200, 7048207, 7048227, 7048321, 7060507, 7060528
81333M
 
81333M ROD, LINK
7048207, 7048227, 7048321, 7055324, 7060507, 7060528
97844M
 
97844M ROD, THROTTLE LEVER
7040202, 7040206, 7040706, 7040716, 7048227, 7048321, 7055324, 7055524, 7060522
Back to top