97718M Mariner ROD, CHOKE LINK


97718M ROD, CHOKE LINK Mariner 7040202, 7040206, 7040706, 7040716 ROD
97718M ROD, CHOKE LINK Mariner
Rating:
93

Buy ROD, CHOKE LINK 97718M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Compatible models:

Mariner entire parts catalog list:

7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040706 1986,1990,1992
7040716 1986

Information:


Table 1
Diagnostic Trouble Code for the Water-in-Fuel Sensor
J1939 Code Code Description Comments
97-3 Water In Fuel Indicator : Voltage Above Normal The ECM detects the following conditions:
An open circuit in the Water-In-Fuel (WIF) sensor circuit.
The warning lamp will stay on when the "indicator lamp self check" has been completed. The ECM will disable the function to detect water in fuel while the code is active.
Note: The keyswitch must have been in the "OFF" position for at least 15 seconds to enable the 97-3 diagnostic check. The 97-3 diagnostic check only occurs once in a keycycle, immediately after the keyswitch is turned to the "ON" position.
Water-in-Fuel Sensor OperationThe WIF sensor is a normally open sensor. During normal operation, there will be no signal sent from the WIF sensor to the ECM. If water is detected in the fuel, the sensor will send a signal to the ECM. If the signal remains constant for 5 seconds, a 97-15 diagnostic code will become active. If the signal remains constant for 30 minutes, a 97-16 diagnostic will become active. These diagnostic codes can also be caused by a short in the WIF sensor circuit.
Illustration 1 g06450675
Schematic diagram for the WIF sensor
Note: All connectors may not be shown. Refer to the Electrical Schematic for the application for details of any connectors between the WIF sensor connector and the ECM connectors.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Turn the keyswitch to the OFF position.
B. Thoroughly inspect the connector for the WIF sensor and any interface connectors between the WIF sensor and the ECM connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".
C. Perform a 30 N (6.7 lb) pull test on each of the wires in the WIF sensor connector and any interface connectors that are associated with the WIF sensor.
D. Check the harness for abrasions, for pinch points, and for corrosion.
Note: Do not disconnect the ECM connector at this stage. The ECM can only be disconnected and reconnected 10 times before damage to the harness connector may occur.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify


Parts rod Mariner:

83468M
 
83468M ROD, LOCK
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716
83542M
 
83542M ROD, SHIFT
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716
83595M
 
83595M ROD
7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716
83921M
ROD
83921M ROD
7025208CW, 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716, 7060522
82988M
 
82988M ROD, CHOKE LINK
7040202, 7040206, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
97844M
 
97844M ROD, THROTTLE LEVER
7040202, 7040206, 7040706, 7040716, 7048227, 7048321, 7055324, 7055524, 7060522
84101M
 
84101M ROD,MAGNETO CONTROL
7010209, 7015529, 7040202, 7040206, 7040208, 7040328, 7040706, 7040716
97743M
 
97743M ROD
7040202, 7040206, 7040706, 7040716
Back to top