97844M Mariner ROD, THROTTLE LEVER


97844M ROD, THROTTLE LEVER Mariner 7040202, 7040206, 7040706, 7040716, 7048227, 7048321, 7055324, 7055524, 7060522 ROD

Buy ROD, THROTTLE LEVER 97844M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

Mariner entire parts catalog list:

7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040706 1986,1990,1992
7040716 1986
7048227 1977
7048321 1981
7055324 1984,1985,1988,1989
7055524 1984,1985
7060522 1982

Information:


Illustration 1 g01194649
Manual Barring Group
(1) Gear
(2) Shaft
(3) Knob
(4) Stem
(5) Slot
Illustration 2 g01194658
Manual Barring Group
(5) Slot
(6) Spacer
(7) Guide The manual barring group provides a means of slowly turning the flywheel in order to perform service work on the engine.Note: Prelube the engine as you rotate the crankshaft during the normal maintenance operations. Refer to the Testing And Adjusting Section of this manual.A 3/4 inch hex drive on the end of shaft (2) is used to turn gear (1). Guide (7) must be loosened before the shaft is engaged or the shaft is turned.Shaft (2) is spring loaded. The shaft must be pushed toward the flywheel in order to engage gear (1) in the flywheel ring gear.The shaft can be engaged in position against the flywheel by pushing in on knob (3). Stem (4) engages in slot (5) of shaft (2). When the knob is pushed inward, the O-ring seals shut off the pressure air source (signal to the relay valve) to the starting motor. The loss of air pressure will prevent the start-up of the engine.The barring group can be used to prevent the rotation of the crankshaft. The inside of spacer (6) is splined. Shaft (2) and the flywheel will be locked in position when the manual barring group is engaged and guide (7) is tightened according to the torque that is listed in the engine's Specifications manual.When the manual barring group is not active, this component must be disengaged from the flywheel. Lock this component in position. Tighten the guide to the torque that is listed in the engine's Specifications manual.Manual Barring Group (50:1)
Illustration 3 g01194661
Manual Barring Group (50:1 reduction)
(1) Shaft
(2) Locking nut
(3) Adapter
(4) Knob An electric wrench or an air wrench may be used with the manual barring group in order to turn the engine slowly. The manual barring group is used while service work is being performed.Use the


Parts rod Mariner:

83468M
 
83468M ROD, LOCK
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716
83542M
 
83542M ROD, SHIFT
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716
83595M
 
83595M ROD
7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716
83921M
ROD
83921M ROD
7025208CW, 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716, 7060522
81408M
 
81408M ROD, SHIFT - LOWER
7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
81333M
 
81333M ROD, LINK
7048207, 7048227, 7048321, 7055324, 7060507, 7060528
98943M
 
98943M ROD, CONTROL
7048227, 7048321, 7055324, 7055524
81337M
 
81337M ROD, CHOKE
7055524, 7060507, 7060522, 7060528
Back to top