42647A 1 Mariner BEARING ASSEMBLY, Roller


42647A 1 BEARING ASSEMBLY, Roller Mariner 7002201DK, 7115473JD, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 7135473GD, 7135473HD, 7135473KD, 7135826, 7135D73RD, 7135D73UY, 7135D73ZY, 7135V13ID, 7135V13UB, 7135V13ZB, 7150413ED, 7150413HD, 7150413LD, 7150413RD, 7150413UY, BEARING
42647A 1 BEARING ASSEMBLY, Roller Mariner
Rating:
83

Buy BEARING ASSEMBLY, Roller 42647A 1 Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$48.00
 

13-08-2024

CN: OVERSEE2018
OVERSEE 31-42647A1 Roller Bearing for Mercury Outboard Motor 65-300HP OMC 387817 18-1117, metallochrome
OVERSEE Fit Mercury / Mariner / Mercruiser / OMC / Johnson / Evinrude Drive Shaft Roller Bearing 65-300 HP || Order number Mercury / MerCruiser aftermant part: 42647A1 || Equal to Mercury / MerCruiser OEM: 31-42647A1, 42647, F694057 OMC / Johnson / Evinrude OEM: 0387817, 0778255, 5007751 || High Quality with Worthy Price. Please save your time on useless products. || Kind Remind: Please check OEM part number before purchase!!! If you are not sure on chosen part number, please provide your engine nameplate or serial number to check compatibility.
$69.99

03-12-2024
0.38[0.17] Pounds
US: Modern Boat Sales, I
Mercury - Mercruiser Bearing Assy, 31-42647A-1
Quiksilver
Number on catalog scheme: 8
 

Mariner entire parts catalog list:

7002201DK 1995
7115473JD 2000
71354120D 1990,1991
7135412AD 1992,1993,1994,1995
7135412ED 1996,1997,1998
7135412HD 1999
7135412JD 2000,2001,2002,2003,2004,2005
7135417PD 1989
7135473GD 1998
7135473HD 1999
7135473KD 2001,2002,2003
7135826 1986,1987,1988
7135D73RD 2004,2005
7135D73UY 2006
7135D73ZY 2006
7135V13ID 2006,2007
7135V13UB 2006
7135V13ZB 2006
7150413ED 1996,1997,1998
7150413HD 1999
7150413LD 2002,2003
7150413RD 2004,2005
7150413UY 2006
7150413ZY 2006
7150423JD 2000,2001
7150629 1979,1980,1982,1984,1985
7175412PD 1989
7175413AD 1992,1993,1994,1995
7175413PD 1989,1990
7175413YD 1991
7175423HD 1999
7175629 1979,1980,1985,1986,1988
7200412PD 1989,1990
7200413JD 2000
7200413UY 2006
7200413ZY 2006
7200423UY 2006
7200473FD 1997
7200473GD 1998
7200473HD 1999
7200473JD 2000
7200473KD 2001,2002
7200620 1980,1982,1983,1984,1985,1986,1988
7200D73IY 2006
7200D73MD 2003
7200D73RD 2004,2005,2006
7200D73ZY 2006
7200V13IR 2006
7200V23ID 2006
7200V23IR 2006,2007
7220727 1987,1988
7225412CD 1994,1995,1996,1997,1998
7225412HD 1999,2000,2001
7225413DD 1995,1996,1997,1998
7225413HD 1999,2000,2001
7225413IY 2006
7225413LD 2002,2003
7225413RD 2004,2005,2006
7225413ZY 2006
7225E73MD 2003,2004
7225V13ID 2006
7225V13IR 2006,2007
7225V13TF 2005
7225V13UB 2006
7225V13ZB 2006
7225V23ID 2006,2007
7225V23IR 2006,2007
7225V24IB 2007
7225V24ID 2006
7250423IY 2006
7250V13ID 2006,2007
7250V23IR 2006
7275V23ID 2006
7275V23IR 2006,2007
7300V23ID 2006

Information:


Illustration 1 g01276413
Schematic for the engine temperature sensors
Illustration 2 g01285043
(1) Engine coolant temperature sensor (2) Intake manifold air temperature sensor (3) Fuel temperature sensorTest Step 1. Inspect the Electrical Connectors and the Wiring
Remove electrical power from the ECM.
Thoroughly inspect all electrical connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Illustration 3 g01285082
(4) J2/P2ECM connector
Illustration 4 g01285091
P2 terminals that are associated with the engine temperature sensors (P2-32) Engine coolant temperature (P2-18) Sensor return (P2-35) Intake manifold air temperature (P2-33) Fuel temperature
Illustration 5 g01155187
Harness connector for the temperature sensors (1) Sensor signal (2) Sensor return
Perform a 45 N (10 lb) pull test on each of the wires at the connectors for the temperature sensors.
Check the allen head screw on each ECM connector and the customer connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and wiring for abrasions and for pinch points from each sensor to the ECM.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The connectors and wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector.
Restore electrical power to the ECM.
Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
Check for an active 03 or 04 diagnostic code.Expected Result:No diagnostic codes are active.Results:
OK - No diagnostic codes are active.Repair: The problem appears to be resolved. The problem may have been related to a faulty connection in the harness. Carefully reinspect the connectors and wiring. Refer to Troubleshooting, "Electrical Connectors - Inspect" for additional information.STOP
Not OK - A 03 diagnostic code is active at this time. The ECM detects an open circuit condition. Proceed to Test Step 4.
Not OK - A 04 diagnostic code is active at this time. The ECM detects a short circuit condition. Proceed to Test Step 3.Test Step 3. Create an Open Circuit by Disconnecting the Sensor Connector
Remove electrical power from the ECM.
Disconnect the suspect sensor from the harness at the sensor connector.
Restore electrical power to the ECM.
Access the "Active Diagnostic Codes" screen on Cat ET. Check for an active 03 diagnostic code for the suspect sensor.Note: Wait at least 30 seconds for activation of the diagnostic codes.
Remove electrical power from the ECM.Expected Result:A 03 diagnostic code is now active for the suspect sensor.Results:
OK - A 03 diagnostic code became active after the sensor was disconnected.Repair: There may be a problem with the sensor. Temporarily connect a new sensor to the harness, but do not install the new sensor in the engine. Verify that there are no active diagnostic codes for the sensor. If there are no active diagnostic codes for the sensor, permanently install the new sensor. Clear any logged diagnostic codes.STOP
Not OK - The 04 diagnostic code is still present while the sensor is disconnected from the harness. The sensor is OK. There is a problem in the harness between the ECM and the sensor connector. There may be a problem with the ECM. Leave the suspect sensor disconnected. Proceed to Test Step 5.Test Step 4. Short the Suspect Sensor at the Harness Connector
Remove electrical power from the ECM.
Disconnect the suspect sensor at the harness connector.
Fabricate a jumper wire that is long enough to short circuit the two terminals at the connector for the suspect sensor. Crimp connector pins to each end of the jumper wire.
Install the jumper wire between terminal 1 (sensor signal) and terminal 2 (sensor return) on the harness side of the suspect sensor's connector.
Restore electrical power to the ECM.
Monitor the "Active Diagnostic Codes" screen on Cat ET after installing the jumper wire. Check for an active 04 diagnostic code.Note: Wait at least 30 seconds for activation of the 04 diagnostic code.
Remove electrical power from the ECM.Expected Result:A 04 diagnostic code is now active for the suspect sensor.Results:
OK - A 04 diagnostic code is active when the jumper wire is installed.Repair: There may be a problem with the sensor. Temporarily connect a new senso


Parts bearing Mariner:

67923
 
67923 BEARING, Ball (LOWER)
7002201DK, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135417PD, 7135473GD, 7135473HD, 7135826, 7150413ED, 7150413HD, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175413AD, 7175413PD, 7175413YD, 7175423HD, 7175629, 7200412PD, 7200473FD, 7200473GD, 720
86637
 
86637 BEARING
7031203GD, 7031207LF, 7031312TB, 7041203GB, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7150629, 7175629, 7200620, 7250422PD, 7F25203JB, 7F25203LB
814103
BEARING
814103 BEARING
7150453PD, 7175412PD, 7200412PD
816974
BEARING, Thrust
816974 BEARING, Thrust
7200413JD, 7225412CD, 7225412HD, 7225413DD, 7225413HD
43012A04
BEARING ASSEMBLY
43012A04 BEARING ASSEMBLY
7075D73ZY, 7100412HB, 7115412TB, 7200D73IY, 7225413IY, 7250423IY
88258001
BEARING, Needle
88258001 BEARING, Needle
7075D73UY, 7075D73ZY, 7090D73RD, 7200D73IY, 7200D73RD, 7200D73ZY, 7225413IY, 7225413RD, 7225413ZY, 7225E73MD, 7250423IY
Back to top