95497M Mariner RUBBER HANDLE, TWIST GRIP


95497M RUBBER HANDLE, TWIST GRIP Mariner 7008204, 7008208, 7008226, 7010209, 7015529, 7020201, 7025200, 7025207PW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207PW, 7040706, 7040716, 7055324 RUBBER
95497M RUBBER HANDLE, TWIST GRIP Mariner
Rating:
103

Buy RUBBER HANDLE, TWIST GRIP 95497M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Mariner entire parts catalog list:

7008204 1984,1985,1986
7008208 1978
7008226 1986
7010209 1979,1983,1984,1985,1986
7015529 1979
7020201 1981
7025200 1980
7025207PW 1989,1990,1991,1992,1993
7025500 1980
7026226 1986,1988
7028527 1977
7030200 1980
7030205 1985,1986,1987,1988,1989,1990
7030301 1981
7030320 1980,1990,1992
7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040207PW 1989,1990,1991,1992,1993
7040706 1986,1990,1992
7040716 1986
7055324 1984,1985,1988,1989

Information:


Illustration 1 g01041707
SchematicTest Step 1. Check for Connector Damage.
Turn the keyswitch to the OFF position.
Thoroughly inspect the ECM connectors J1/P1 and J2/P2. Inspect all of the other connectors. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connectors (allen head screw) for the proper torque of 6 1 N m (53 9 lb in).
Check the harness and the wiring for abrasion and for pinch points.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion or of pinch points.Results:
OK - The connectors and wiring are okay. Proceed to Test Step 2.
Not OK - The connectors and/or wiring need repair.Repair: Repair the connectors and/or wiring or replace the connectors and/or wiring. Stop.Test Step 2. Check for Electrical Shorts in the Harness.
Disconnect the ECM connectors for the ECM.
Disconnect any module that is connected to the CAT data link.
Measure the resistance at the following points. Wiggle the harness during the measurement in order to reveal an intermittent short.
CAT data link + to CAT data link -
CAT data link + to -Battery terminal
CAT data link - to -Battery terminal
CAT data link + to +Battery terminal
CAT data link - to +Battery terminal
CAT data link + to engine ground
CAT data link - to engine groundExpected Result:The resistance is more than 20,000 Ohms for each measurement.Results:
OK - The resistance is greater than 20,000 Ohms. Proceed to Test Step 3.
Not OK - The resistance is less than 20,000 Ohms. There is a short in the harness or in the connectors.Repair: Repair the connector and/or wiring or replace the connector and/or wiring. Stop.Test Step 3. Check the Resistance through the Harness for an Open Circuit.
Disconnect the ECM connectors for the ECM.
Disconnect any module that is connected to the CAT data link.
Short the wires of the CAT data link together. Create the short at P1:9 and P1:8 of the ECM connector.
Set an ohmmeter on the 200 Ohm scale. Measure the resistance between the terminals of the CAT data link + and the CAT data link -. Measure the resistance at the connectors for the ECM. Measure the resistance between the terminals of any module that was connected to the CAT data link. Wiggle the harness during the measurements in order to reveal an intermittent open condition.
Reconnect all connectors and modules.Expected Result:The resistance is less than 5 Ohms for each measurement.Results:
OK - The resistance is less than 5 Ohms for each measurement.Repair: The harness is okay. There could be a problem with a module or with the ECM. Connect the suspect module on another engine. If the problem returns on the other engine, replace the suspect module. Turn the keyswitch to the ON position. Turn the keyswitch to the ON position. If the diagnostic code is still present, replace the ECM. Refer to the diagnostic procedure Troubleshooting, "Replacing the ECM". Stop.
Not OK - The resistance is greater than 5 Ohms for each measurement.Repair: There is an open circuit or there is excessive resistance in the harness. Repair the connectors and/or wiring or replace the connectors and/or wiring. Stop.


Parts rubber Mariner:

82021M
RUBBER
82021M RUBBER
7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
84854M
 
84854M RUBBER HANDLE, TWIST GRIP
7020201, 7025200, 7025207NW, 7025500, 7028527, 7030200, 7040208, 7040328, 7040507, 7048227, 7048321
83490M
 
83490M RUBBER, SEAL
7010209, 7015529, 7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716
81426M
 
81426M RUBBER, WATER SEAL
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
81427M
 
81427M RUBBER, WATER SEAL
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
84038M
84037M
84297M
Back to top